1. Introduction
This manual provides comprehensive instructions for the proper setup, operation, and maintenance of your Schellenberg Smart DRIVE 60930 2-channel remote control. This device is designed for convenient control of up to two compatible Schellenberg Smart DRIVE M, L, and XL garage door operators.
Figure 1: Schellenberg Smart DRIVE 60930 2-channel remote control and its packaging.
2. Safety Information
- Always keep the remote control out of reach of children.
- Ensure the garage door operator is visible during operation, especially when controlled by multiple wireless handheld transmitters, to prevent accidents.
- Do not expose the remote control to extreme temperatures, moisture, or direct sunlight.
- Only use the specified battery type (CR2032 lithium button battery).
- Dispose of used batteries according to local regulations.
3. Package Contents
The package includes the following items:
- 1 x Smart DRIVE Wireless Transmitter (2-channel)
- 1 x CR2032 Lithium Button Battery (pre-installed)
- 1 x Assembly Instructions
- 1 x Loop, yellow (pre-mounted)
- 1 x Loop, gray (additional)
Figure 2: Remote control, battery, and interchangeable loop.
4. Product Features
- Comfortable control of up to 2 garage door drives.
- Easy learning process with the garage door opener.
- Operates on a radio frequency of 868.4 MHz.
- Includes an additional gray ring for color identification of the handheld transmitter.
- Compatible with Schellenberg Smart DRIVE M, L, and XL garage door automations.
5. Specifications
| Specification | Value |
|---|---|
| Manufacturer | Schellenberg |
| Model Number | 60930 |
| Product Dimensions | 6.8 x 2.9 x 1.1 cm |
| Weight | 90 grams |
| Color | Anthracite |
| Style | 2 Channel Handheld Transmitter |
| Power Source | Hand operated (Battery) |
| Battery Type | Lithium (CR2032) |
| Radio Frequency | 868.4 MHz |
Figure 3: Dimensions of the remote control.
6. Setup and Programming
6.1. Copying an Existing Remote Control (First Set Way)
This method allows you to duplicate the signal from an existing remote control to your new Schellenberg Smart DRIVE 60930 remote. Ensure both remotes are in close proximity during this process.
- Verify that the existing remote control is functioning correctly by pressing its buttons.
- On the new remote control, simultaneously press and hold the two top buttons (A and B) until the LED flashes.
- Release button A while continuing to hold button B.
- Press button A three times. The LED will flash rapidly. Release button B.
- Place the original remote control and the new remote control side-by-side.
- On the new remote, long-press the button you wish to program (e.g., button A). The LED will flash slowly.
- On the original remote, long-press the corresponding button. The LED on the new remote will flash rapidly, indicating successful copying.
- Repeat for other buttons if desired.
Video 1: This video demonstrates the 'First Set Way' for copying an existing remote control's signal to the Schellenberg Smart DRIVE 60930. It shows how to activate the copying mode on both remotes and transfer the signal.
6.2. Learning Method for Receiver (Second Set Way)
This method involves programming the remote control directly to your garage door operator's receiver unit. Refer to your garage door operator's manual for specific receiver button locations.
- On the new remote control, simultaneously press and hold the two top buttons (A and B) until the LED flashes.
- Release button A while continuing to hold button B.
- Press button A three times. The LED will flash rapidly. Release button B.
- Locate the learning button on your garage door operator's receiver.
- Press the learning button on the receiver. The receiver's indicator light will begin to flash.
- Within 3-5 seconds, long-press the desired button on your new Schellenberg remote control. The receiver's light will flash quickly and then go out, indicating successful learning.
- Test the remote control to ensure it operates the garage door correctly.
Video 2: This video illustrates the 'Second Set Way' for programming the Schellenberg Smart DRIVE 60930 remote control to a receiver. It details the steps to put the receiver into learning mode and then pair the remote control.
7. Operating Instructions
Once programmed, operating your Schellenberg Smart DRIVE 60930 remote control is straightforward:
- To open or close the garage door, press the corresponding programmed button on the remote control.
- Ensure you have a clear line of sight to the garage door and its operator during activation.
Figure 4: Using the remote control from inside a vehicle.
Figure 5: Activating the garage door with the remote control.
8. Maintenance
8.1. Battery Replacement
The remote control is powered by a CR2032 lithium button battery. If the remote control's range decreases or the LED does not light up, the battery may need to be replaced.
- Carefully open the remote control casing.
- Remove the old CR2032 battery.
- Insert a new CR2032 battery, ensuring correct polarity (+/-).
- Close the remote control casing securely.
8.2. Cleaning
Wipe the remote control with a soft, dry cloth. Do not use abrasive cleaners or solvents.
9. Troubleshooting
- Remote not working after programming: Ensure the programming steps were followed precisely. Try reprogramming the remote. Check the battery.
- Reduced range: Replace the battery. Ensure there are no obstructions between the remote and the receiver. Large metal objects or other radio devices can interfere with the signal.
- LED not lighting up: The battery may be depleted or incorrectly inserted. Replace the battery and check its polarity.
10. Warranty and Support
For warranty information, technical support, or further assistance, please refer to the official Schellenberg website or contact their customer service. You can also visit the Schellenberg Store on Amazon for additional product information and accessories.
