SUNPIE 4-Pod RGBW Rock Lights User Manual

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your SUNPIE 4-Pod RGBW Rock Lights. These lights are designed to provide customizable illumination for off-road vehicles, including trucks, SUVs, ATVs, UTVs, and boats. The RGBW design includes a dedicated white LED for pure white light, enhancing visibility and aesthetic appeal.

2. Safety Information

Read all instructions carefully before installation and use.

• Always disconnect the vehicle's battery before performing any electrical work to prevent electrical shock or short circuits.
• Ensure all wiring connections are secure and properly insulated to prevent water ingress and electrical hazards.
• Mount the rock lights in locations that do not obstruct vehicle operation or safety features.
• Avoid looking directly into the light source when illuminated, as it may cause temporary vision impairment.
• If you are unsure about any part of the installation process, consult a qualified professional.

3. Package Contents

Verify that all components are present before beginning installation:

• 4 x SUNPIE RGBW Rock Light Pods
• 1 x Control Box (Bluetooth enabled)
• 1 x Remote Control
• Mounting Hardware (screws, nuts, washers)
• Wiring Harnesses (approximately 11.5 feet per light)

Image: Overview of the SUNPIE 4-Pod RGBW Rock Lights kit, showing the four light pods, control box, and remote control.

Image: Close-up of the control box with wiring and the included remote control for the rock lights.

4. Setup & Installation

Proper installation is crucial for optimal performance and longevity of your rock lights. Follow these steps carefully:

4.1 Pre-Installation

1. Plan Mounting Locations: Determine the best positions for each rock light pod to achieve desired illumination. Common locations include wheel wells, under the chassis, or along the frame.
2. Test Fit: Temporarily position the lights and route the wiring to ensure sufficient cable length and proper fitment.
3. Disconnect Power: Disconnect the negative terminal of your vehicle's battery before proceeding with any wiring.

4.2 Mounting the Rock Lights

1. Position each rock light pod in its chosen location.
2. Mark the drilling points for the mounting screws.
3. Drill pilot holes using an appropriate drill bit size for the provided screws.
4. Secure each light pod using the provided screws and mounting hardware. Ensure they are firmly attached to withstand vehicle movement and off-road conditions.

Image: Example of SUNPIE rock lights installed on a truck, demonstrating the red illumination in the wheel well area.

Image: Example of SUNPIE rock lights installed on a truck, demonstrating the blue illumination in the wheel well area.

4.3 Wiring Connections

1. Connect each rock light pod to the main wiring harness from the control box. The connectors are designed to be waterproof; ensure they are fully seated and tightened.
2. Route all wiring away from moving parts, exhaust systems, and sharp edges. Use zip ties or cable clips to secure the wiring.
3. Connect the red wire from the control box to a 12V positive power source (e.g., battery terminal or an accessory fuse). It is recommended to use an inline fuse for protection.
4. Connect the black wire from the control box to a reliable ground point on the vehicle chassis or battery negative terminal.
5. Mount the control box in a dry, secure location, away from direct heat and moisture.

4.4 App Installation and Pairing

1. Download the App: Search for "Sunpie LED Light" or similar in your smartphone's app store (iOS or Android).
2. Enable Bluetooth: Ensure Bluetooth is enabled on your smartphone.
3. Power On Lights: Reconnect the vehicle's battery. The lights should power on.
4. Pair with App: Open the "Sunpie LED Light" app. The app should automatically detect and connect to the control box. If not, follow the in-app instructions for manual pairing.

Image: Screenshots of the mobile application interface, illustrating options for color selection, music synchronization, and voice control.

5. Operation

Your SUNPIE RGBW Rock Lights can be controlled via the dedicated mobile application or the included remote control.

5.1 Using the Mobile Application

The "Sunpie LED Light" app offers comprehensive control over your rock lights:

• Color Mode: Select from a wide spectrum of colors using the color wheel or predefined color swatches. The RGBW design allows for a pure white light option.
• Music Mode: Synchronize the lights with music playing on your phone or through the app's microphone input. The lights will pulse and change color according to the audio rhythm.
• Voice Mode: Control the lights using voice commands (if supported by the app version).
• Strobe Modes: Choose from over 20 different strobe and flashing patterns for dynamic effects.
• Brightness Adjustment: Adjust the intensity of the lights to your preference.

5.2 Using the Remote Control

The remote control provides quick access to essential functions:

• Power On/Off: Turn the lights on or off.
• Color Selection: Directly select common colors (Red, Green, Blue, White, etc.).
• Brightness Control: Adjust light intensity.
• Mode Selection: Cycle through various flashing, fading, and strobe modes.
• Music Sync: Activate music synchronization (may require the app to be running in the background for full functionality).

6. Maintenance

Regular maintenance ensures the longevity and optimal performance of your rock lights:

• Cleaning: Periodically clean the light pods with a soft cloth and mild soap to remove dirt and debris. Avoid abrasive cleaners.
• Wiring Inspection: Regularly check all wiring connections for signs of wear, corrosion, or loose connections. Secure any loose wiring.
• Mounting Hardware: Ensure all mounting screws and brackets remain tight. Re-tighten if necessary.
• Waterproofing: Verify that all waterproof connectors are properly sealed, especially after off-road use or exposure to harsh weather.

7. Troubleshooting

If you encounter issues with your SUNPIE RGBW Rock Lights, refer to the following common problems and solutions:

7.1 Lights Not Turning On

• Check Power Connection: Ensure the red wire is securely connected to a 12V power source and the black wire to a good ground.
• Check Fuse: Verify that any inline fuse is not blown. Replace if necessary.
• Battery Connection: Confirm the vehicle's battery is properly connected and charged.
• Control Box: Ensure the control box is receiving power and its connections to the light pods are secure.

7.2 App Cannot Connect to Lights

• Bluetooth Enabled: Confirm Bluetooth is active on your smartphone.
• App Permissions: Ensure the app has necessary Bluetooth and location permissions.
• Restart App/Phone: Close and reopen the app, or restart your smartphone.
• Power Cycle Lights: Disconnect and reconnect power to the control box to reset it.
• Proximity: Ensure your phone is within close range of the control box.

7.3 Incorrect or Inconsistent Colors

• Wiring Check: Verify that all light pods are correctly connected to the control box and that no wires are damaged or swapped.
• App/Remote Sync: Ensure the app or remote is properly synced and sending the correct commands. Try power cycling the lights and reconnecting.
• Individual Pod Issue: If only one pod is displaying incorrect colors, it may indicate a fault with that specific pod or its connection.

8. Specifications

Note: Specifications are subject to change without notice.

9. Warranty & Support

SUNPIE stands behind its products. If you have any questions or encounter issues during the use of this product, please contact our customer service team. We are committed to providing support and assistance.

For customer service inquiries, please refer to the contact information provided with your purchase or visit the official SUNPIE website.

"We're always here for our customers. We provide customer support service and are willing to help you at any time."