Brook Xone SE Adapter Instruction Manual

1. Product Overview

The Brook Xone SE Adapter (Type-C Version) is designed to enhance your gaming experience by allowing Xbox One Elite Series 2 and Xbox Series X/S controllers to be used across multiple platforms, including Xbox Series X/S, Nintendo Switch, PlayStation 4, and PC (XID, Steam). This adapter integrates seamlessly, providing features such as motion control, turbo function, button remapping, and audio support.

Figure 1: Brook Xone SE Adapter (Type-C Version) and retail packaging.

Figure 2: Front view of the Xone SE Adapter, showing the function buttons and Brook branding.

Figure 3: Side view of the Xone SE Adapter, highlighting its compact design.

2. Setup and Installation

Follow these steps to properly set up your Brook Xone SE Adapter with your controller and gaming console.

2.1 Attaching the Adapter to Your Controller

Ensure your Xbox One Elite Series 2 or Xbox Series X/S controller is powered off.
Align the Type-C connector of the Xone SE Adapter with the USB-C port on your controller.
Gently push the adapter firmly into the controller's port until it is securely seated. Ensure the 3.5mm audio jack on the adapter also aligns with the controller's audio port.

Brook Xone SE Adapter attached to an Xbox controller

Figure 4: The Xone SE Adapter securely attached to an Xbox controller, ready for use.

Video 1: Demonstrates how to ensure the adapter is fully inserted into your controller for proper connection.

2.2 Initial Connection to Consoles/PC

The adapter supports various platforms. The connection method may vary slightly depending on the target system.

Nintendo Switch:
1. Switch the toggle switch button on the adapter to "NS" mode.
2. Wake up the controller and press and hold the "Bluetooth" button on the Xone SE Adapter for 2 seconds.
3. The LED on the adapter will blink red and blue alternately. Wait for a few seconds until the LED turns blue, indicating a successful connection.
Video 2: Guide on wirelessly connecting the Xone SE Adapter to a Nintendo Switch.
Video 3: Guide on wired connection of the Xone SE Adapter to a Nintendo Switch.
PlayStation 4:
1. Switch the toggle switch button on the adapter to "PS4" mode.
2. Connect the adapter to your PS4 via a USB cable (not included) or follow wireless pairing instructions if applicable.
3. Compatible PS4 games are playable on PS5 consoles. PS5-specific games are not supported.
PC (XID, Steam):
1. Connect the adapter to your PC via a USB cable. The system should recognize it as an XID device.
2. For Steam, ensure your controller settings are configured to recognize the connected device.
Xbox Series X/S & Xbox One:
1. The adapter allows your Xbox controllers to connect to these consoles. Ensure the adapter is properly attached to the controller.

3. Operating Instructions and Features

The Xone SE Adapter provides several advanced functions to enhance your gameplay.

3.1 Motion Control

The adapter supports motion control for PlayStation 4 and Nintendo Switch games, adding an immersive layer to your gaming experience.

Xbox controller with Xone SE Adapter demonstrating motion control

Figure 5: Motion control functionality enabled by the Xone SE Adapter on compatible consoles.

Video 4: Official trailer showcasing the features of the Brook Xone Adapter SE, including motion control.

3.2 Turbo and Remap Functions

The adapter allows for easy setup of Turbo and Remap functions for PS4, Switch, and PC, providing customizable control options.

Turbo Function: Press the dedicated Turbo button on the adapter to activate or adjust the turbo speed.
Remap Function: Use the Remap button to reassign controller inputs. Refer to the specific instructions on the Brook website for detailed remapping procedures.
Button Hold Function: This feature allows a button to be held down automatically.

Close-up of Xone SE Adapter buttons for Turbo and Remap

Figure 6: The function buttons on the Xone SE Adapter for activating Turbo and Remap features.

Video 5: Demonstrates how to set up and cancel remap functions on the Xone SE Adapter.

3.3 Audio Function

The 3.5mm microphone headset jack on the adapter supports audio for PS4 and Xbox One consoles, allowing you to use your preferred headset.

Video 6: Illustrates the use of the simulated touchpad function on the Xone SE Adapter.

3.4 Emulate PS4 Touch Pad

The adapter can emulate the PS4 touchpad via a dedicated Function Key, providing full compatibility with PS4 games.

4. Maintenance

To ensure the longevity and optimal performance of your Xone SE Adapter, please follow these maintenance guidelines:

Cleaning: Use a soft, dry cloth to clean the adapter. Avoid using harsh chemicals or abrasive materials.
Storage: Store the adapter in a cool, dry place away from direct sunlight and extreme temperatures.
Handling: Handle the adapter with care. Avoid dropping it or subjecting it to strong impacts.
Firmware Updates: Regularly check the official Brook website for firmware updates. Updates can improve compatibility, add new features, and resolve potential issues. It is recommended to update the firmware before initial use.

5. Troubleshooting

If you encounter any issues with your Xone SE Adapter, please refer to the following common troubleshooting steps:

Problem	Possible Cause	Solution
Adapter not recognized by console/PC.	Incorrect mode selected, loose connection, outdated firmware.	Ensure the toggle switch is set to the correct console mode (NS/PS4). Verify the adapter is fully and securely inserted into the controller. Check for and install the latest firmware from the Brook website. Try a different USB port or cable if using a wired connection.
Motion control not working or inaccurate.	Not supported on current platform, calibration needed, interference.	Confirm motion control is supported on your specific console (PS4/Switch). Perform a motion control calibration if available (check Brook website for instructions). Ensure no strong magnetic fields or electronic interference are nearby.
Audio not working through headset.	Headset not fully plugged in, incorrect audio settings, not supported on platform.	Ensure the 3.5mm headset jack is fully inserted into the adapter. Verify audio settings on your console/PC are configured for the connected headset. Confirm audio function is supported on your specific console (PS4/Xbox One).
Controller disconnects frequently.	Low controller battery, wireless interference, adapter not fully seated.	Charge your controller's battery. Minimize wireless interference by moving closer to the console or removing other wireless devices. Re-seat the adapter firmly into the controller. Update adapter firmware.

6. Specifications

Model: X one SE Adapter - Type C Version
Brand: Brook
Compatible Controllers: Xbox One Elite Series 2, Xbox Series X/S Controllers
Compatible Platforms: Xbox Series X/S, Nintendo Switch, PlayStation 4, PC (XID, Steam), Xbox One
Connectivity: USB-C (to controller), Wireless (Bluetooth)
Features: Motion Control (PS4/Switch), Turbo, Remap, Button Hold, Audio Function (3.5mm headset for PS4/Xbox One), PS4 Touchpad Emulation
Dimensions: 2.36 x 1.77 x 0.79 inches
Weight: 2.12 ounces
Color: Black
Country of Origin: Taiwan

7. Warranty and Support

For warranty information, technical support, and the latest firmware updates, please visit the official Brook website:

Brook Official Website

You can also refer to the official User Manual PDF provided by the manufacturer for additional details:

Download User Manual (PDF)

	Brook Wingman NS Lite Converter User Guide This guide provides instructions for using the Brook Wingman NS Lite Converter, a wireless controller adapter for Nintendo Switch, Switch OLED, Switch Lite, and PC. It details connection steps, LED indicators, wireless pairing, and advanced features like Turbo and Button Remap settings for various controllers including Xbox, PlayStation, and Switch Pro.
	Brook Wingman PS2 Converter User Manual Comprehensive user manual for the Brook Wingman PS2 Converter, detailing connection, LED display, button mapping, turbo function, remapping, and input mode switching for various game consoles and controllers.
	Brook Wingman XE 2 Converter User Guide User guide for the Brook Wingman XE 2, a controller converter adapter compatible with PlayStation, Nintendo Switch, and PC. Learn about setup, firmware updates, Turbo, and Remap functions.
	Brook X One Adapter: Connect Xbox One Controller to PS4, Switch, and PC Comprehensive guide for the Brook X One Adapter, enabling Xbox One controllers on PlayStation 4, Nintendo Switch, and PC. Features setup instructions, mode switching, turbo functionality, button remapping, and technical specifications.
	Brook XB Fighting Board User Guide: Connections, Features, and Console Compatibility Detailed user manual for the Brook XB Fighting Board, covering setup, wiring, button functions, turbo settings, SOCD modes, and compatibility with Xbox Original, Xbox 360, Xbox One, and Xbox Series consoles.
	Brook Gen-5X Fighting Board User Guide A comprehensive user guide for the Brook Gen-5X Fighting Board, detailing its features, connection methods, button configurations, and advanced settings for various gaming consoles and PC.

Brook X one SE Adapter - Type C Version