Introduction
The Directed Electronics DS3 Remote Start Interface System is designed to enhance vehicle security and convenience. As a global leader in security and control telematics, this system aims to make your vehicle experience more secure, comfortable, and enjoyable. This manual provides essential information for the proper setup, operation, and maintenance of your DS3 system.
Figure 1: Directed Electronics DS3 Remote Start Interface System module.
Setup and Installation
Proper installation of the DS3 system is crucial for its functionality and your vehicle's safety. It is highly recommended that installation be performed by a qualified professional installer.
General Installation Steps (Professional Installation Recommended):
- Vehicle Preparation: Ensure the vehicle's battery is disconnected before beginning any electrical work.
- Module Placement: Select a secure and discreet location within the vehicle for mounting the DS3 module, away from excessive heat or moisture.
- Wiring Connections: Carefully follow the detailed wiring diagrams provided with the professional installation kit. This typically involves connecting to the vehicle's ignition, power, ground, data bus, and other relevant circuits.
- Module Programming: Once all physical connections are made, the DS3 module will need to be programmed to your specific vehicle using specialized tools and software. This step integrates the system with the vehicle's onboard computer.
- Testing: After programming, thoroughly test all functions of the remote start and interface system to ensure correct operation and vehicle compatibility.
Note: Incorrect installation can lead to vehicle damage, system malfunction, or safety hazards. Always consult the professional installation guide or a certified technician.
Operating Instructions
Once installed and programmed, the DS3 system allows for remote control of various vehicle functions. Specific operations may vary based on your vehicle and the remote control device used (e.g., factory key fob, dedicated remote, smartphone app).
Common Operations:
- Remote Start: Typically activated by pressing a specific button sequence on your remote control (e.g., lock button three times, or a dedicated remote start button). The vehicle will start and run for a pre-set duration.
- Remote Stop: To turn off the engine after remote starting, repeat the remote start button sequence or press a dedicated stop button.
- Key Takeover: After remote starting, enter the vehicle, insert the key into the ignition, turn it to the ON/RUN position, and press the brake pedal. This transfers control from the remote start system to the vehicle's ignition.
- Door Lock/Unlock: Use your remote control to lock or unlock the vehicle doors.
- Trunk Release: If configured, a dedicated button on your remote may release the vehicle's trunk.
Refer to your specific remote control's user guide for exact button functions and sequences.
Maintenance
The Directed Electronics DS3 system is designed for reliable operation with minimal maintenance. Follow these general guidelines:
- Keep Dry: Ensure the module and its connections remain dry and free from moisture.
- Avoid Extreme Temperatures: While designed for automotive environments, prolonged exposure to extreme temperatures outside normal operating ranges can affect performance.
- Remote Control Batteries: Replace batteries in your remote control devices as needed to ensure consistent performance. Refer to your remote's manual for battery type and replacement instructions.
- Software Updates: Periodically, your installer may recommend software updates for the DS3 module to improve performance or add new features. These updates should only be performed by a qualified technician.
Troubleshooting
If you experience issues with your DS3 system, consider the following common troubleshooting steps:
- System Not Responding:
- Check the battery in your remote control.
- Ensure you are within range of the vehicle.
- Verify that the vehicle's hood is closed, and the parking brake is engaged (if required by your vehicle's setup).
- Vehicle Fails to Remote Start:
- Confirm the vehicle is in Park (automatic transmission) or Neutral with the parking brake engaged (manual transmission, if configured).
- Check if the vehicle's check engine light is on, which can prevent remote start.
- Ensure all doors, trunk, and hood are securely closed.
- Short Remote Range:
- Replace the remote control battery.
- Avoid areas with high radio frequency interference.
If problems persist, contact your authorized Directed Electronics dealer or professional installer for assistance.
Specifications
| Model Number: | DS3 |
| Product Dimensions: | 10.5 x 4 x 3.5 inches |
| Item Weight: | 1.1 pounds |
| Brand: | Directed |
| Manufacturer: | Viper |
| Country of Origin: | China |
| Other Display Features: | Wireless |
Warranty and Support
Directed Electronics products are backed by a limited warranty. For specific warranty terms and conditions, please refer to the documentation provided with your purchase or visit the official Directed Electronics website. For technical support, service, or warranty claims, please contact your authorized dealer or the Directed Electronics customer support team.
Keep your proof of purchase for warranty purposes.
