1. Introduction
Thank you for choosing BERTSCHAT® Heated Insoles. These rechargeable insoles are designed to provide warmth and comfort for your feet in various conditions, offering up to 14 hours of battery life. They are ideal for outdoor activities such as fishing, hiking, hunting, motorcycling, and for use in work boots. This manual provides essential information for the safe and effective use of your heated insoles.
2. Safety Information
Please read all safety warnings carefully before using the product.
- Do not use the product near water or in humid environments.
- Do not charge the insoles at low temperatures below 5 °C (41 °F).
- Ensure the charging cable is securely connected to the insole to prevent short circuits.
- Keep out of reach of children.
- Do not puncture, disassemble, or modify the insoles.
- If you experience discomfort or excessive heat, immediately turn off the insoles and remove them.
3. Package Contents
Verify that all items are present in your package:
- 1 pair of BERTSCHAT® Heated Insoles
- 1 Remote Control
- 1 USB Charging Cable
- 1 Wall Charger (Power Adapter)
- User Manual (this document)
Image: The complete package contents, showing the heated insoles, remote control, USB charging cable, wall adapter, and a small instruction booklet.
4. Setup
4.1 Initial Charging
Before first use, fully charge the insoles. Each insole has a built-in rechargeable battery.
- Locate the charging port on the side or heel of each insole.
- Connect the USB charging cable to the insoles and then to the wall charger.
- Plug the wall charger into a power outlet.
- The indicator light on the insoles will show charging status (e.g., red for charging, green for fully charged).
- Allow approximately 3-4 hours for a full charge.
Image: A BERTSCHAT heated insole connected to its charger, illustrating the charging process.
4.2 Inserting Insoles into Footwear
The insoles are designed to fit most types of footwear. You may need to remove your existing insoles first.
- Ensure the insoles are fully charged.
- Carefully slide each heated insole into your shoe or boot, ensuring it lies flat and comfortably.
- Make sure the insole is not folded or creased, as this can damage the heating elements.
Image: A user demonstrating the insertion of a BERTSCHAT heated insole into a boot, with snow on the ground.
5. Operating Instructions
Your BERTSCHAT® Heated Insoles come with a remote control for easy temperature adjustment.
5.1 Remote Control Functions
The remote control has four buttons:
- Power Button (Orange Circle): Press to turn the insoles ON or OFF.
- High (H): Sets the insoles to the highest heat level.
- Medium (M): Sets the insoles to a medium heat level.
- Low (L): Sets the insoles to the lowest heat level.
Image: A close-up of the remote control for the heated insoles, highlighting its buttons.
5.2 Adjusting Temperature
To adjust the heat level:
- Press the Power button on the remote to turn on the insoles.
- Select your desired heat level (H, M, or L) by pressing the corresponding button on the remote.
- The insoles will begin to heat up. The integrated temperature sensor optimizes the foot climate for maximum efficiency.
Image: An illustrative diagram explaining the three temperature settings (High, Middle, Low) and the battery life of up to 14 hours, controlled via the remote.
6. Maintenance
6.1 Cleaning
- Turn off the insoles and disconnect them from any power source before cleaning.
- Wipe the surface of the insoles with a damp cloth. Do not submerge them in water.
- Allow the insoles to air dry completely before storing or recharging.
- Do not use harsh chemicals or abrasive cleaners.
6.2 Storage
- Store the insoles in a cool, dry place away from direct sunlight and extreme temperatures.
- For long-term storage, it is recommended to charge the batteries to about 50% every few months to maintain battery health.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Insoles not heating | Battery is low or depleted. Insoles are not turned on. Remote control battery is low. | Charge the insoles fully. Press the power button on the remote. Replace remote control battery (if applicable, check manual for remote battery type). |
| Short battery life | Using on High setting continuously. Battery degradation over time. | Use on Medium or Low setting for extended periods. Ensure full charge before use. Battery life naturally decreases over many charge cycles. |
| Remote not responding | Remote battery is low or dead. Out of range. Interference. | Replace remote control battery. Move closer to the insoles. Avoid using near strong electromagnetic fields. |
8. Specifications
- Model: B08JYX6CYD
- Size: 38-40 (EU)
- Color: Black
- Material Type: Plastic
- Power Source: Battery
- Battery: 2 x 2200 mAh 3.7V (integrated, rechargeable Lithium-metal)
- Battery Life: Up to 14 hours (depending on heat setting)
- Features: Cushioning, Integrated temperature sensor, Wireless operation
- Dimensions: Approximately 45 x 38 x 13 cm (packaging); 70g (per insole)
- Included Components: 2 heated insoles, 2 x 2200 mAh 3.7V batteries (integrated), remote control, charger.
Image: A detailed view of the BERTSCHAT PRO EDITION heated insoles, highlighting key features and specifications such as battery life and design.
9. Warranty and Support
For warranty information and customer support, please refer to the contact details provided by your retailer or visit the official BERTSCHAT® website. Keep your purchase receipt as proof of purchase.
Manufacturer: BERTSCHAT®
