Konnected UPS Backup Battery - Model B300GA

Introduction

The Konnected UPS Backup Battery (Model B300GA) is a 12V DC power bank designed to provide uninterrupted power to various low-voltage electronic devices during power outages. This device ensures continuous operation for essential smart home components, network equipment like routers and modems, and single-board computers such as the Raspberry Pi. With a 7800 mAh lithium-ion battery, it offers extended runtime, automatically switching to battery power when the main power supply is interrupted.

Image: Front view of the Konnected UPS Backup Battery.

Package Contents

• Konnected Mini-UPS with 7800 mAh battery
• DC male to DC male power cable

Note: A 12V DC power adapter is required for operation and charging, but is not included in the package. Use the adapter provided with your Konnected kit or a separately purchased compatible 12V DC adapter.

Setup Instructions

1. Charge the UPS: Connect your 12V DC power adapter (not included) to the DC IN port of the Konnected UPS. Plug the adapter into a wall outlet. The UPS will begin charging. Allow approximately 8 hours for a full charge.
2. Identify Device Power Requirements: Determine the input voltage and connector type of the device you intend to power (e.g., router, modem, smart home hub). The Konnected UPS provides a 12V DC output via a 2.5 mm ID / 5.5 mm OD barrel connector and a 5V DC / 2.1A output via a USB-A port.
3. Connect Your Device (12V DC): For 12V DC devices, use the provided DC male to DC male power cable. Connect one end to the DC OUT port of the Konnected UPS and the other end to the DC IN port of your device. Ensure the barrel connector sizes are compatible.
4. Connect Your Device (5V USB): For 5V USB-powered devices, connect a standard USB cable from the USB OUT port of the Konnected UPS to your device.
5. Verify Operation: Once connected, your device should power on. The UPS will pass power from the wall adapter to your device while simultaneously charging its internal battery.

Image: Diagram showing the Konnected UPS connected to a router and modem for backup power.

Image: Close-up view of the Konnected UPS showing the DC IN, DC OUT, and USB OUT ports.

Operating Instructions

• Automatic Power Switchover: The UPS automatically detects a loss of incoming 12V DC power and instantly switches to its internal battery to continue powering connected devices without interruption.
• Battery Runtime: The 7800 mAh battery can power devices for up to 14 hours, depending on the power consumption of the connected devices. Lower power devices (e.g., Raspberry Pi, smart home hubs) will have longer runtimes than higher power devices (e.g., WiFi routers).
• LED Indicators: The unit features an LED indicator. A bright LED indicates the unit is powered on and/or charging. During normal operation, the LED remains lit.
• Simultaneous Output: Both the 12V DC barrel output and the 5V USB output can be used simultaneously, provided the total power draw does not exceed the unit's maximum output capacity (30W).

Maintenance

• Charging: For optimal battery life, keep the UPS connected to its 12V DC power adapter when not in use. This ensures the battery remains charged and ready for power outages.
• Temperature: Operate the UPS within the specified temperature range of -20 °C to 45 °C. Avoid exposing the unit to extreme heat or cold, direct sunlight, or high humidity.
• Cleaning: Clean the exterior of the unit with a soft, dry cloth. Do not use liquid cleaners or solvents.
• Battery Replacement: The internal lithium-ion battery is accessible by removing the bottom cover. However, finding a compatible replacement battery pack with the correct specifications and connector may be challenging. It is generally not recommended for user replacement unless experienced with electronics.

Troubleshooting

• Device Not Powering On:
  • Ensure the UPS is charged. Connect it to a 12V DC power adapter and allow sufficient charging time.
  • Verify that the 12V DC power adapter is functioning correctly and providing power to the UPS.
  • Check all cable connections between the UPS and your device. Ensure they are secure and the correct ports are used (DC IN on UPS for charging, DC OUT on UPS for powering devices).
  • Confirm that your device's power requirements (voltage and current) do not exceed the UPS's output capabilities (12V DC / 2.5A or 5V DC / 2.1A).
• UPS Not Charging:
  • Ensure the 12V DC power adapter is properly connected to the DC IN port of the UPS and plugged into a working wall outlet.
  • Verify the 12V DC power adapter is functional. Try it with another compatible device if possible.
• USB Port Not Working:
  • Confirm the UPS is powered on and has sufficient charge.
  • Test with a different USB cable and device to rule out cable or device issues.
  • Ensure the connected USB device does not draw more than 2.1A.
• LED is Too Bright:
  • The LED indicator is designed to be visible. If its brightness is disruptive, consider placing the unit in a less visible location or using a small piece of opaque tape to cover the LED.
• DC Barrel Plug Compatibility:
  • The Konnected UPS uses a 2.1 mm ID / 5.5 mm OD plug for DC input and a 2.5 mm ID / 5.5 mm OD plug for DC output. While the 2.5 mm output plug may fit 2.1 mm input jacks, ensure a secure connection. If your device requires a different size, compatible DC barrel adapters or cables can be purchased separately.

Specifications

Image: Konnected UPS with key dimensions indicated.

Warranty Information

Specific warranty information for the Konnected UPS Backup Battery (Model B300GA) is not available in the provided product data. Please refer to the product packaging or the manufacturer's official website for detailed warranty terms and conditions.

Customer Support

Customer support contact details are not available in the provided product data. For technical assistance or inquiries, please visit the official Konnected website or refer to the contact information provided with your purchase.