TAMIYA Campus Friends Set II Plastic Model Figures (Model 24356) Instruction Manual

1. Safety Information

This model kit contains small parts. Keep out of reach of children under 10 years of age to prevent choking hazards. Adult supervision is recommended during assembly and painting. Always use tools and paints in a well-ventilated area.

2. Package Contents

Verify that all components are present before starting assembly.

• Plastic sprues containing 5 model figures (1/24 scale)
• Plastic sprues containing scooter parts
• Plastic sprues containing various accessories (e.g., guitar case, bags, coffee cups, smartphone)
• Decal sheet
• Instruction sheet

Image Description: A close-up view of various accessories included in the kit, such as a black guitar case, a light blue handbag, a beige tote bag, a brown paper bag, a black smartphone, and a blue rectangular item.

3. Assembly Instructions

Follow the numbered steps on the included instruction sheet for proper assembly.

1. Carefully remove parts from the sprues using a hobby knife or sprue cutters.
2. Smooth any rough edges with a hobby file or sandpaper.
3. Test fit parts before applying adhesive.
4. Apply plastic cement sparingly to join parts. Allow sufficient drying time.
5. Refer to the diagrams for correct part orientation and assembly sequence.

Image Description: Two assembled TAMIYA Campus Friends figures. One male figure is walking with a guitar case, and one female figure is standing with a backpack.

Image Description: A rear view of the assembled TAMIYA Campus Friends Set II scooter model, showing its details and design.

4. Painting Guide

This model kit is supplied unpainted, allowing for personalized customization. Refer to the color guide for recommended TAMIYA paint colors.

1. Clean all assembled parts to remove dust and oils.
2. Apply a primer coat for better paint adhesion and a uniform finish.
3. Use appropriate brushes or an airbrush for painting. Apply thin, even coats.
4. Allow each coat of paint to dry thoroughly before applying the next.
5. Apply decals as instructed on the decal sheet after painting is complete and a gloss coat has been applied.

Image Description: A chart displaying various TAMIYA XF (flat) acrylic paint colors with their corresponding article numbers and descriptions, indicating paints required for the model.

Image Description: A second chart detailing additional TAMIYA X (gloss) acrylic paint colors, their article numbers, and descriptions, providing further paint options for the model.

Image Description: A close-up of two female TAMIYA Campus Friends figures, one holding a coffee cup and the other taking a selfie with a smartphone, demonstrating potential painted finishes.

5. Recommended Tools

The following tools are recommended for optimal assembly and finishing:

• Hobby Knife or Sprue Cutters
• Fine-grit Sandpaper or Hobby File
• Plastic Cement
• Tweezers
• Paint Brushes (various sizes)
• Masking Tape
• Decal Setting Solution

Image Description: An assortment of recommended tools for model assembly, including angled tweezers, a cutter knife, decal scissors, side cutters, a paint brush set, masking tape, and various types of plastic cement and decal adhesives.

6. Maintenance and Care

To preserve the appearance of your finished model:

• Keep the model away from direct sunlight and extreme temperatures.
• Dust gently with a soft brush or compressed air.
• Avoid contact with harsh chemicals or solvents.

Image Description: Two assembled and painted TAMIYA Campus Friends figures standing next to a red sports car model, demonstrating a potential display scenario for the finished figures.

7. Troubleshooting

• Parts not fitting: Ensure all sprue gates are fully removed and check for excess plastic. Lightly sand or trim as needed.
• Paint not adhering: Ensure surfaces are clean and free of oils. Apply a primer coat before painting.
• Decals not settling: Use decal setting solution to help decals conform to irregular surfaces.
• Missing parts: Double-check the sprues and packaging. If parts are genuinely missing, contact TAMIYA customer support.

8. Specifications

• Brand: TAMIYA
• Model Name: Campus Friends Set II
• Model Number: 24356-000
• Scale: 1/24
• Material: Plastic
• Number of Figures: 5
• Recommended Age: 10 years and up
• Product Dimensions: Approximately 4.5 x 19.2 x 29.2 inches (package)
• Item Weight: Approximately 6.7 ounces

Image Description: The official box art for the TAMIYA Campus Friends Set II, featuring an illustration of the five figures and a scooter in a campus setting, along with product details and the TAMIYA logo.

9. Warranty and Support

For product support, missing parts, or warranty inquiries, please contact TAMIYA customer service. Refer to the official TAMIYA website for contact information and additional resources.

Visit TAMIYA Official Website