Introduction
Thank you for choosing the Auriol Radio-Controlled Wall Clock. This clock is designed to provide accurate timekeeping by automatically synchronizing with a radio time signal. It also features integrated displays for temperature and humidity, making it a versatile addition to any indoor space. Please read this manual carefully before first use to ensure proper operation and to get the most out of your new clock.
Safety Instructions
- Keep the clock away from extreme temperatures, direct sunlight, and high humidity.
- Do not expose the clock to water or other liquids.
- Use only the specified battery type.
- Insert batteries with correct polarity (+/-).
- Remove exhausted batteries immediately to prevent leakage and damage.
- Do not dispose of batteries in fire.
- This product is intended for indoor use only.
- Do not attempt to disassemble or repair the clock yourself. Refer to qualified service personnel.
Package Contents
Please check the package contents upon unpacking:
- 1 x Auriol Radio-Controlled Wall Clock
- 1 x Instruction Manual (this document)
Product Overview
Image: Front view of the Auriol Radio-Controlled Wall Clock. The clock features a white face with large black numbers for hours, black minute and hour hands, and a red second hand. Below the center, there are two smaller dials: one on the left for humidity (labeled '% HUMIDITY') and one on the right for temperature (labeled 'TEMPERATURE °C °F'). A radio signal icon is visible near the 6 o'clock position. The clock has a silver-colored frame.
The Auriol Radio-Controlled Wall Clock combines classic analog time display with modern radio-controlled accuracy. It also integrates a hygrometer to measure humidity and a thermometer to measure temperature, providing comprehensive environmental information at a glance.
Setup
1. Battery Installation
- Open the battery compartment cover on the back of the clock.
- Insert one AA 1.5V battery (not included) according to the polarity markings (+ and -) inside the compartment.
- Close the battery compartment cover securely.
2. Initial Synchronization (Radio Control)
After inserting the battery, the clock will automatically start searching for the DCF77 radio time signal. The hands will typically move to the 12 o'clock position and then begin to search for the signal. This process can take several minutes, or up to 24 hours in areas with weak reception.
- Place the clock near a window, away from electronic devices that might cause interference (e.g., TVs, computers, microwaves).
- Avoid placing the clock on metal surfaces.
- Once the signal is received, the clock will automatically set itself to the correct time, including adjusting for Daylight Saving Time (DST).
3. Manual Time Setting (If Needed)
If the clock does not synchronize automatically after an extended period (e.g., 24 hours), or if you are in an area without DCF77 signal coverage, you may need to set the time manually. Look for a small button or wheel on the back of the clock, usually labeled "SET" or "M.SET".
- Press and hold the manual setting button until the hands start to move.
- Release the button when the hands reach the desired time. Some models require repeated short presses to advance the hands.
- The clock will then resume searching for the radio signal. If it finds the signal, it will override the manual setting.
Operating the Clock
Time Display
The large analog hands display the current time (hours, minutes, seconds). The radio-controlled function ensures the time is always accurate and automatically adjusts for Daylight Saving Time.
Temperature Display
The smaller dial on the right side of the clock face indicates the ambient temperature. Readings are typically provided in both Celsius (°C) and Fahrenheit (°F).
Humidity Display
The smaller dial on the left side of the clock face indicates the relative humidity in percentage (%).
Maintenance
Cleaning
Wipe the clock with a soft, dry cloth. Do not use abrasive cleaners or solvents, as they may damage the surface.
Battery Replacement
When the clock hands stop moving or the time becomes inaccurate, it is time to replace the battery. Follow the battery installation steps in the "Setup" section.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Clock does not set time automatically. | Weak or no radio signal; battery low or incorrectly inserted. |
|
| Time is incorrect. | Interference during synchronization; clock was moved during synchronization. |
|
| Humidity/Temperature readings seem inaccurate. | Sensor obstruction; extreme environmental conditions; not calibrated. |
|
Specifications
- Brand: Owim
- Model Number: 321928-1901
- Type: Radio-Controlled Wall Clock with Analog Display
- Special Features: Radio-controlled time, Temperature display, Humidity display
- Power Source: Battery Powered (1 x AA 1.5V)
- Dimensions (approx.): 26.6 x 26 x 5.6 cm (Package dimensions)
- Weight (approx.): 620 grams (Item weight)
- Indoor/Outdoor Use: Indoor Use
Warranty and Support
For warranty information and customer support, please refer to the warranty card included with your purchase or contact the manufacturer directly. Details regarding warranty periods and service procedures are typically provided by the retailer or manufacturer at the time of purchase.
Please retain your proof of purchase for any warranty claims.
