Cisco PWR-C5-600WAC Catalyst 9200 600W AC Switch Power Supply User Manual

1. Introduction

This manual provides essential information for the safe and efficient installation, operation, and maintenance of the Cisco PWR-C5-600WAC 600W AC Power Supply. This power supply is designed as a hot-plug, plug-in module for compatible Cisco Catalyst 9200 series networking devices.

2. Safety Information

WARNING: Electrical Hazard

• Always disconnect power from the device before installing or removing the power supply, unless specifically designed for hot-swapping and the procedure is followed correctly.
• Ensure proper grounding of the equipment.
• Do not operate the power supply if it is damaged or has exposed wiring.
• Only qualified personnel should perform installation and servicing.

3. Product Overview

The Cisco PWR-C5-600WAC is a 600-watt AC power supply unit designed for Cisco Catalyst 9200 series switches. It features a hot-plug, plug-in module design for easy installation and replacement, ensuring continuous operation of your networking infrastructure.

Figure 1: Rear view of the PWR-C5-600WAC power supply. This image displays the standard AC power input connector, a hexagonal ventilation grille, and a metal release latch on the side, indicating its hot-plug capability. Status indicator lights are visible through the grille.

Key Features:

• Device Type: Hot-plug, plug-in module power supply
• Power Capacity: 600 Watts AC
• Form Factor: Flex ATX
• Cooling Method: Air-cooled
• Compatibility: Designed for Cisco Catalyst 9200 series networking devices

4. Setup and Installation

The PWR-C5-600WAC is a hot-plug power supply, allowing for installation or replacement without powering down the host device, provided the host device supports hot-swapping.

Installation Steps:

1. Prepare the Slot: Identify the empty power supply slot in your Cisco Catalyst 9200 switch. If replacing an existing power supply, ensure it is properly disengaged and removed.
2. Orient the Power Supply: Hold the PWR-C5-600WAC with the AC inlet facing outwards and the release latch aligned with the slot.
3. Insert the Power Supply: Gently slide the power supply into the designated slot until it is fully seated. You should feel a click as the power supply engages with the backplane connector.
4. Secure the Latch: Ensure the release latch is securely closed, locking the power supply in place.
5. Connect Power: Connect a standard AC power cord to the power inlet on the power supply and then to a grounded AC power source.
6. Verify Operation: Check the status indicator LEDs on the power supply and the host switch to confirm proper operation. Refer to your switch's documentation for LED status interpretations.

Removal Steps:

1. Disconnect Power: Disconnect the AC power cord from the power supply.
2. Release Latch: Open the release latch on the power supply.
3. Remove Power Supply: Gently pull the power supply out of the slot.

5. Operating Instructions

Once installed and powered, the PWR-C5-600WAC operates automatically to provide power to the connected networking device. Monitor the status LEDs on the power supply and the host switch for operational status.

• Green LED: Indicates normal operation and power output.
• Amber/Orange LED: May indicate a fault or warning condition. Consult the switch's documentation for specific error codes.
• Off LED: Indicates no power input or a critical failure.

6. Maintenance

The Cisco PWR-C5-600WAC power supply is designed for minimal maintenance. Adhere to the following guidelines to ensure optimal performance and longevity:

• Ventilation: Ensure that the ventilation openings on the power supply and the host device are clear of obstructions to allow for proper airflow and cooling.
• Cleaning: Periodically clean the exterior of the power supply and the switch chassis with a soft, dry cloth. Do not use liquid cleaners or aerosols.
• Environmental Conditions: Operate the power supply within the recommended environmental specifications of the host switch (temperature, humidity).

7. Troubleshooting

If you encounter issues with your PWR-C5-600WAC power supply, consider the following troubleshooting steps:

• No Power/LED Off:
  • Verify the AC power cord is securely connected to both the power supply and the power outlet.
  • Check the power outlet for functionality by plugging in another device.
  • Ensure the power supply is fully seated in its slot within the switch.
• Amber/Orange LED:
  • This often indicates a fault. Consult the specific error messages or LED patterns in your Cisco Catalyst 9200 switch's documentation.
  • Try reseating the power supply.
  • If possible, test with a known good power supply or in a different slot.
• Intermittent Power:
  • Check all power connections for looseness.
  • Ensure the power source is stable and meets the power supply's requirements.

If issues persist after these steps, contact technical support.

8. Specifications

9. Warranty and Support

This product is offered as an Amazon Renewed item. Amazon Renewed products are professionally inspected and tested to work and look like new. They are eligible for replacement or refund under the Amazon Renewed Guarantee if you are not satisfied with your purchase.

For technical support related to the Cisco Catalyst 9200 series switches or specific power supply issues not covered in this manual, please refer to the official Cisco documentation or contact Cisco technical support.