Introduction
This manual provides detailed instructions for the proper use, setup, and maintenance of your AUTOOL Intelligent Electronic Refrigerant Temperature Control Clips. These accessories are designed to enhance the functionality of compatible AUTOOL refrigerant tables by providing accurate temperature measurements.
The AUTOOL temperature control clips are Type-K thermocouple clamps, engineered for high accuracy and reliability in HVAC temperature measurement applications. They are compatible with multimeters, clamp meters, and thermometers that accept a Type-K temperature probe.
Product Features
- High Accuracy: Increased jaw strength ensures optimal thermal contact with pipes for quick and precise temperature readings.
- Reliable & Convenient: Specifically designed for HVAC temperature measurement, compatible with Type-K temperature probe inputs on various testing devices.
- Handy & Compact Design: Features spring-equipped clamping jaws for a firm and secure grip on pipes, facilitating easy temperature reading.
- Wide Application: Ideal for industrial temperature measurement, particularly in heating, ventilation, air conditioning (HVAC), and plumbing systems.
- Compatibility: Designed for use with AUTOOL LM110, LM120, LM120+, LM150, and LM160 refrigerant tables.
- Diameter: Compatible with pipes up to 0.35 inches in diameter.
Package Contents
Upon opening the package, please verify that all items are present and in good condition.
- 2 x AUTOOL Intelligent Electronic Refrigerant Temperature Control Clips (Type-K Thermocouple Clamps)
Figure 1: Overview of the two AUTOOL temperature control clips included in the package.
Setup
- Unpack the Clips: Carefully remove the temperature control clips from their packaging.
- Inspect for Damage: Before use, visually inspect each clip and its cable for any signs of damage. Do not use if damaged.
- Connect to Compatible Device: Plug the connector of the temperature control clip cable into the appropriate Type-K thermocouple input port on your AUTOOL LM110, LM120, LM120+, LM150, LM160 refrigerant table, or other compatible multimeter/thermometer. Ensure a secure connection.
- Prepare for Measurement: Ensure the pipe or surface you intend to measure is clean and free of debris to ensure optimal thermal contact.
Figure 2: Close-up view of the temperature control clips, highlighting the connection points and clamping jaws.
Operating Instructions
Follow these steps to accurately measure temperature using the AUTOOL temperature control clips:
- Power On Device: Turn on your compatible AUTOOL refrigerant table or measurement device.
- Select Temperature Mode: If applicable, set your measurement device to the appropriate temperature measurement mode (e.g., Type-K thermocouple).
- Attach the Clip: Open the jaws of the temperature control clip by squeezing the handles. Carefully position the clip onto the pipe or surface you wish to measure. Release the handles to allow the spring-loaded jaws to firmly grip the pipe. Ensure the sensor pads make full contact with the surface for accurate readings.
- Read Measurement: Observe the temperature reading displayed on your connected device. Allow a few moments for the reading to stabilize.
- Remove the Clip: Once the measurement is complete, squeeze the handles to release the clip from the pipe.
Figure 3: Demonstrating how to open the clamping jaws of the temperature control clip.
Figure 4: The temperature control clip with its jaws fully open, ready to be attached to a pipe.
Maintenance
Proper maintenance will ensure the longevity and accuracy of your AUTOOL temperature control clips.
- Cleaning: After each use, wipe the sensor pads and the body of the clip with a soft, dry cloth. For stubborn dirt, a slightly damp cloth can be used, but ensure the device is completely dry before storage or next use. Do not use abrasive cleaners or solvents.
- Storage: Store the clips in a clean, dry environment, away from direct sunlight and extreme temperatures. Avoid tangling the cables.
- Inspection: Periodically inspect the cables for fraying or damage, and the clamping mechanism for proper function.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Inaccurate or fluctuating readings | Poor contact with pipe; dirty sensor pads; incompatible device settings. | Ensure firm and full contact of sensor pads with the pipe. Clean sensor pads. Verify your measurement device is set to Type-K thermocouple mode. |
| No reading on device | Loose connection; damaged cable/clip; device not powered on or in correct mode. | Check cable connection to the measurement device. Inspect cable and clip for visible damage. Ensure measurement device is powered on and in the correct input mode. |
| Clip does not grip pipe firmly | Pipe diameter too large; spring mechanism issue. | Ensure pipe diameter is within the 0.35-inch limit. If the spring mechanism is faulty, the clip may need replacement. |
Specifications
| Attribute | Value |
|---|---|
| Model Number | MCD11027-1 |
| Type | Type-K Thermocouple Clamp |
| Compatibility | AUTOOL LM110, LM120, LM120+, LM150, LM160 refrigerant tables, and other devices accepting Type-K probes. |
| Max Pipe Diameter | 0.35 inches |
| Item Weight | 6.4 ounces (approx. per pair) |
| Package Dimensions | 7.2 x 4.5 x 2 inches |
Warranty and Support
AUTOOL products are manufactured to high quality standards. For warranty information, technical support, or service inquiries, please contact AUTOOL customer service through their official website or the retailer from whom you purchased the product. Please have your product model number (MCD11027-1) and purchase details ready when contacting support.
For more information, visit the AUTOOL Store on Amazon.