Artiss King Bed Frame (Model: BFRAME-E-LUMI-K-BK-ABC) Instruction Manual

1. Introduction

Thank you for choosing the Artiss King Bed Frame. This manual provides essential information for the safe assembly, operation, and maintenance of your new bed frame. Please read these instructions carefully before beginning assembly and retain them for future reference.

This bed frame features a robust design with a gas lift mechanism for under-bed storage and an integrated RGB LED headboard for ambient lighting.

2. Safety Information

• Maximum Load Capacity: The bed frame is designed to support a maximum weight of 300 kg. Do not exceed this limit.
• Assembly: Assembly should be performed by at least two adults. Ensure all components are securely fastened before use.
• Gas Lift Mechanism: Exercise caution when operating the gas lift. Keep hands and fingers clear of moving parts. Ensure the mattress is properly seated before lifting or lowering.
• LED Lighting: The LED system operates on low voltage. Do not attempt to modify or repair the LED strips or wiring.
• Placement: Position the bed frame on a flat, stable surface.
• Children and Pets: Keep children and pets away from the bed frame during assembly and operation of the gas lift mechanism.

3. Package Contents

Verify that all components listed below are present before beginning assembly. If any parts are missing or damaged, please contact your retailer.

• Artiss LUMI LED Gas Lift Bed Frame (King Size) components
• Remote Control for LED lighting
• Assembly Manual (detailed step-by-step instructions)
• Hardware pack (screws, bolts, tools)

4. Setup and Assembly

Refer to the dedicated Assembly Manual included in your package for detailed, step-by-step instructions, diagrams, and a complete parts list. The following is a general overview:

1. Unpack: Carefully unpack all components and lay them out on a clean, soft surface to prevent scratches.
2. Identify Parts: Match all parts against the parts list in the Assembly Manual.
3. Assemble Frame: Follow the instructions to assemble the main bed frame, headboard, and side rails.
4. Install Gas Lift Mechanism: Attach the gas lift mechanism according to the manual's diagrams. Ensure it is correctly aligned and secured.
5. Install Slats: Secure the plywood slats into the designated positions on the bed frame.
6. Connect LED: Connect the LED strip to the power supply and controller as instructed.

Important: Two people are recommended for assembly to ensure safety and ease of handling large components.

This image illustrates the overall dimensions of the Artiss King Bed Frame, including its length, width, and height measurements for the headboard and base.

A front-angle view of the Artiss King Bed Frame, highlighting its black upholstered design and the wooden slat system that supports the mattress.

5. Operating Instructions

5.1 Gas Lift Storage

The gas lift mechanism allows easy access to the storage space beneath the bed. Ensure your mattress is placed on the bed frame before operating the gas lift.

1. To Lift: Stand at the foot of the bed. Firmly grasp the handle or edge of the bed base and lift upwards. The hydraulic pistons will assist in raising the platform smoothly.
2. To Lower: Gently push the bed base downwards. The gas lift will offer resistance, allowing for a controlled descent. Ensure no objects or body parts are in the path of the descending platform.

This image demonstrates the gas lift functionality of the bed frame, showing the mattress platform lifted to access the spacious storage compartment beneath.

5.2 RGB LED Lighting

The integrated RGB LED lighting system is controlled by the included remote control.

• Battery: The remote control requires a CR2025 or CR2032 battery (not included). Insert the battery with the correct polarity.
• Operation: Point the remote control directly at the receiver located on the bed frame.
• Functions:
  • Power On/Off: Press the power button to turn the LEDs on or off.
  • Color Selection: Choose from 16 customizable colors using the color buttons.
  • Mode Selection: Select from 4 dynamic modes (e.g., flash, strobe, fade, smooth) to change the lighting effect.
  • Brightness Adjustment: Use the brightness buttons to increase or decrease the light intensity.

The Artiss King Bed Frame is shown with its integrated RGB LED lighting turned on, creating an ambient glow around the bed base.

6. Maintenance

• Cleaning: For the PVC leather upholstery, wipe with a soft, damp cloth. Avoid harsh chemicals or abrasive cleaners.
• Hardware Check: Periodically check all bolts and screws to ensure they remain tight. Re-tighten if necessary.
• Gas Lift: The gas lift mechanism is generally maintenance-free. Do not lubricate the pistons. If operation becomes stiff or noisy, refer to the troubleshooting section.
• LEDs: The LED strips are designed for long life. If an issue occurs, refer to troubleshooting.

7. Troubleshooting

• Gas Lift is Stiff/Not Lifting:
  • Ensure the mattress is on the bed frame. The gas lift requires the weight of a mattress to function correctly.
  • Check for any obstructions preventing movement.
  • Verify that the gas lift pistons are correctly installed and not damaged.
• LED Lights Not Working:
  • Check if the remote control battery (CR2025/CR2032) is inserted correctly and has power.
  • Ensure the remote is pointed directly at the LED receiver.
  • Verify all power connections to the LED strip and controller are secure.
  • Check the power adapter is plugged into a working outlet.
• Bed Frame is Wobbly/Noisy:
  • Re-tighten all assembly bolts and screws.
  • Ensure the bed frame is on a level surface.
  • Check that all slats are properly seated and not damaged.

If problems persist, please contact your retailer for assistance.

8. Specifications

9. Warranty and Support

For warranty information and customer support, please refer to the documentation provided by your retailer or contact the manufacturer directly. Keep your proof of purchase for any warranty claims.