Product Overview
The Rocelco MA1 is a single monitor arm designed for ergonomic viewing and workspace optimization. It features Gas Piston Counterbalance Motion Assist (GPCMA) for effortless adjustment. This monitor arm supports screens from 13 to 27 inches, with a maximum weight capacity of 14.3 lbs (6.5 kg). It includes integrated USB 2.0 and audio ports for convenient device connectivity and charging. Cable management channels are built-in to maintain a tidy workspace. The MA1 offers two mounting options: desk clamp and grommet.
Figure 1: Rocelco MA1 Features Overview
Setup and Installation
The Rocelco MA1 monitor arm offers two primary installation methods: Desk Clamp and Grommet Clamp. Please follow the instructions carefully for your chosen method.
1. Desk Clamp Mounting
This method is suitable for desks with an edge where the clamp can be securely attached. Ensure your desk thickness is between 0.5" and 3.3".
- Remove the bottom cover of the monitor arm base to access the mounting plate.
- Attach the desk clamp bracket to the monitor arm base using the provided screws and Allen key. Ensure it is securely fastened.
- Position the monitor arm on the edge of your desk.
- Tighten the C-clamp screw until the arm is firmly secured to the desk. Do not overtighten.
Video 1: Rocelco MA1 Assembly and Installation. This video demonstrates both desk clamp and grommet mounting options, as well as monitor attachment and cable management.
2. Grommet Clamp Mounting
This method is for desks with an existing grommet hole or if you plan to drill one. Ensure your desk thickness is between 0.5" and 3.3".
- Remove the bottom cover of the monitor arm base.
- Attach the grommet plate to the monitor arm base using the provided screws and Allen key. Insert the long bolt through the center hole.
- Insert the long bolt through the grommet hole in your desk.
- From underneath the desk, secure the arm by tightening the washer and nut onto the long bolt.
Refer to Video 1 for a visual guide on grommet clamp mounting.
3. Monitor Installation
The MA1 supports VESA mounting patterns of 75x75mm and 100x100mm.
- Attach the VESA plate from the monitor arm to the back of your monitor using the appropriate screws. Ensure the screws are tightened securely but do not overtighten.
- Carefully slide the monitor (with the attached VESA plate) onto the arm's mounting head.
- Secure the monitor to the arm by tightening the locking screw on the mounting head.
Refer to Video 1 for a visual guide on monitor installation.
Operating Instructions and Adjustments
The Rocelco MA1 monitor arm offers a range of adjustments for optimal viewing comfort.
Rotation
The monitor can be rotated +180° to -180° (portrait to landscape orientation). Simply grasp the edges of your monitor and rotate it to the desired position.
Video 2: Instructional Video for MA1. This video demonstrates the various adjustments including rotation, swivel, tilt, and gas spring functionality.
Swivel
The arm allows for a swivel range of +90° to -90° at the monitor connection point, and 360° at the center and base. This enables you to easily share your screen or adjust your viewing angle.
Refer to Video 2 for a visual guide on swivel adjustments.
Tilt
The monitor can be tilted +90° to -45° to reduce glare and optimize viewing angles. Loosen the tilt adjustment screw, set the desired angle, and then re-tighten the screw.
Refer to Video 2 for a visual guide on tilt adjustments.
Gas Spring Tension Adjustment
The gas spring provides effortless height adjustment. If the monitor does not stay in position or is difficult to move, adjust the gas spring tension. Use the provided Allen key to turn the tension screw located on the arm. Turn clockwise to increase tension for heavier monitors, and counter-clockwise to decrease tension for lighter monitors. Adjust gradually until the monitor holds its position smoothly.
Refer to Video 2 for a visual guide on gas spring tension adjustment.
USB and Audio Ports
The base of the monitor arm includes integrated USB 2.0 and audio ports. Connect the corresponding cables from the monitor arm to your computer's USB and audio ports to enable these features. This allows for convenient charging and connectivity of your devices directly from the monitor arm base.
Cable Management
The MA1 features integrated cable management channels to keep your workspace tidy and organized.
- Open the cable covers located on the underside of the arm segments.
- Route your monitor cables (power, video, USB, audio) through these channels.
- Close the cable covers to secure the cables in place.
Refer to Video 1 for a visual guide on cable management.
Maintenance
To ensure the longevity and optimal performance of your Rocelco MA1 monitor arm, follow these maintenance guidelines:
- Cleaning: Wipe the arm surfaces with a soft, damp cloth. Avoid abrasive cleaners or solvents that may damage the finish.
- Periodic Checks: Periodically check all screws and connections to ensure they remain tight. Re-tighten if necessary, but do not overtighten.
- Gas Spring: The gas spring is designed for long-term use and generally requires no maintenance. If you notice a change in its performance, re-adjust the tension as described in the "Operating Instructions and Adjustments" section.
Troubleshooting
If you encounter issues with your Rocelco MA1 monitor arm, refer to the following common solutions:
- Monitor Sags or Won't Stay Up: The gas spring tension may be too low for your monitor's weight. Increase the gas spring tension by turning the adjustment screw clockwise with the provided Allen key.
- Monitor is Difficult to Move Up or Down: The gas spring tension may be too high. Decrease the gas spring tension by turning the adjustment screw counter-clockwise.
- Arm Feels Loose or Wobbly: Ensure all mounting screws (desk clamp or grommet) are securely tightened. Also, check the screws connecting the VESA plate to the monitor and the arm segments.
- USB/Audio Ports Not Working: Verify that the USB and audio cables from the monitor arm base are correctly connected to the corresponding ports on your computer. Check your computer's device manager or sound settings to ensure the ports are recognized and enabled.
Specifications
| Feature | Detail |
|---|---|
| Model Number | R MA1 |
| Screen Size Compatibility | 13" - 27" |
| Weight Capacity | Up to 14.3 lbs (6.5 kg) |
| VESA Mounting Patterns | 75x75mm, 100x100mm |
| Rotation | +180° ~ -180° |
| Swivel | +90° ~ -90° (at monitor), 360° (at center and base) |
| Tilt | +90° ~ -45° |
| Movement Type | Articulating, Gas Spring Assist |
| Mounting Type | Desk Clamp, Grommet Clamp |
| Desk Thickness (Clamp/Grommet) | 0.5" to 3.3" |
| Integrated Ports | USB 2.0, Audio (Mic/Headphone) |
| Material | Alloy Steel |
| Color | Black |
Warranty and Support
For warranty information, product support, or to purchase additional protection plans, please refer to the official Rocelco website or contact their customer service. Protection plans are available for 2-year, 3-year, and complete protection options.
- 2-Year Protection Plan: Available for purchase.
- 3-Year Protection Plan: Available for purchase.
- Complete Protect: Monthly plan covering eligible past and future purchases.
Contact information for Rocelco can typically be found on their official website or through the retailer where the product was purchased.
