Adviace 5 Burner Kit SS
Adviace Grill Replacement Parts User Manual
Brand: Adviace | Model: 5 Burner Kit SS
Introduction
This user manual provides essential information for the Adviace Grill Replacement Parts kit, designed to restore the performance of your gas grill. This kit includes high-quality stainless steel pipe burners, heat plates, and electronic ignitors, specifically compatible with various Nexgrill, Members Mark, Backyard Grill, and BBQ Pro models. Follow these instructions to ensure a proper installation and extend the life of your grill.
Image: Transform your grill from old and rusted to new and efficient with Adviace replacement parts.
Product Components
The Adviace Grill Replacement Parts kit for 5-burner models typically includes the following components, crafted from durable stainless steel for longevity and performance:
- 5 Stainless Steel Pipe Burners
- 5 Stainless Steel Heat Plates (Heat Tents)
- 5 Electronic Ignitors (with wires)
Image: Overview of the Adviace 5-burner grill replacement kit components.
Image: Detailed view of a stainless steel heat plate, emphasizing its durable construction.
Image: Detailed view of the high-hardness stainless steel main burners.
Compatibility
This replacement kit is designed to fit a range of gas grill models. Please verify your grill model number to ensure compatibility.
- Nexgrill: 720-0888, 720-0888N, 720-0830H, 720-0864, 720-0864M, 720-0882S, 720-0888A, 720-0894F, 720-0896CA, 720-0958A, 720-0864R, 720-0925S, 720-0898, 730-0898, 720-0783E, 720-0830A, 720-0830D.
- Members Mark: 720-0882D, 720-0830F, 720-0830G.
- BBQ Pro: 122.47207610, 122.57901710, 720-0894R.
- Kenmore: 122.20148510, 122.33492410, 720-0830A.
- BHG Grill: 720-0783H.
- Backyard Grill: 720-0888M.
- Kitchen Aid Grill: 720-0830A.
Image: Compatible grill models for Adviace replacement parts.
Installation Guide
Before beginning installation, ensure your grill is completely cool and disconnected from its gas supply. It is recommended to replace components one at a time to maintain proper alignment and simplify the process.
- Preparation: Remove cooking grates and existing heat plates from your grill.
- Remove Old Burners: Carefully detach the old burners. Note how they are secured, often with cotter pins at the back. You may need needle-nose pliers. If cotter pins are rusted, be prepared to replace them with new ones from a hardware store.
- Disconnect Ignitors: Disconnect the ignitor wires from the old burners. If the screws are rusted, you might need to snip the wires and re-strip them for the new ignitors.
- Install New Burners: Place the new stainless steel pipe burners into position. Secure them with the cotter pins or appropriate fasteners.
- Connect New Ignitors: Attach the new electronic ignitors to the burners. Route the ignitor wires to the main ignitor button assembly. Use small zip ties to manage excess wire for a tidy installation.
- Install Heat Plates: Position the new stainless steel heat plates over the burners.
- Replace Grates: Carefully place the cooking grates back into the grill.
- Test Ignition: Reconnect the gas supply. Press the ignitor button to test each burner. If a burner does not light, check the ignitor wire connection and ensure the spark is aligned with the gas port on the burner. It may take a moment for gas to flow through new burners. Consider replacing the AA battery in the igniter button if issues persist.
Image: New burners and heat plates perfectly installed in the grill.
Maintenance
Regular maintenance of your grill replacement parts will ensure optimal performance and extend their lifespan.
- Cleaning Burners: Periodically clean the burner tubes to prevent blockages from food debris or grease. Use a grill brush or a soft cloth. Ensure burner ports are clear for even flame distribution.
- Cleaning Heat Plates: Clean heat plates after each use to remove grease and food residue. Stainless steel heat plates are easy to clean with warm soapy water and a non-abrasive cloth.
- Inspection: Regularly inspect burners and heat plates for signs of wear, corrosion, or damage. Replace parts as needed to maintain grilling efficiency and safety.
Image: Easy cleaning of the stainless steel heat plates.
Troubleshooting
Refer to the table below for common issues and their potential solutions.
| Issue | Possible Cause | Solution |
|---|---|---|
| Burner not lighting | Clogged ignitor, loose wire, dead battery, gas flow issue | Check ignitor wire connection, replace ignitor battery, clear burner ports, ensure gas supply is open. |
| Uneven flame | Clogged burner ports, damaged burner | Clean burner ports thoroughly. If damage is present, consider replacing the burner. |
| Low flame | Low gas pressure, partially clogged burner | Check gas tank level and regulator. Clean burner ports. |
| Excessive noise/yellow flame | Burner damage, improper air mixture | Inspect burner for damage. Ensure proper installation and alignment. |
Image: Example of even flame distribution from properly functioning burners.
Specifications
Detailed specifications for the Adviace Grill Replacement Parts (5 Burner Kit SS):
| Component | Dimensions | Material |
|---|---|---|
| Pipe Burners | 14 7/8" x 1" Dia | Stainless Steel |
| Heat Plates | 14 9/16" x 4 3/16" | Stainless Steel |
| Ignitors | Standard size | Electronic components |
| Item Weight (entire kit) | 4.88 pounds | N/A |
| Product Dimensions (packaging) | 14.88 x 4.2 x 2 inches | N/A |
Image: Detailed dimensions of the grill replacement parts.
Warranty and Support
Adviace stands behind the quality of its grill replacement parts. For specific warranty information or technical support, please refer to the product packaging or contact Adviace customer service through their official channels. Keep your purchase receipt for warranty claims.
Ask a question about this manual
Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.