1. Introduction
Thank you for choosing the XPCLEOYZ 54x3W LED Par Light. This manual provides essential information for the safe and efficient operation of your new stage lighting system. This product features 54 high-brightness 3W RGBW LEDs, offering a wide range of color mixing capabilities and various control modes, including DMX512, sound activation, and auto programs. Please read this manual thoroughly before installation and operation.
XPCLEOYZ Brand Logo
Figure 1.1: XPCLEOYZ LED Par Lights creating dynamic color and fog effects.
Figure 1.2: XPCLEOYZ LED Par Lights providing ambient lighting for an event.
2. Safety Instructions
- Electrical Safety: Ensure the power supply voltage matches the product's requirements (12V DC). Always disconnect power before cleaning or servicing.
- Ventilation: Do not block ventilation openings. Ensure adequate airflow around the fixture to prevent overheating.
- Indoor Use Only: This product is designed for indoor use. Do not expose to rain, moisture, or extreme temperatures.
- Eye Protection: Avoid direct eye exposure to the light source. The LEDs are bright and can cause discomfort.
- Mounting: Securely mount the fixture using appropriate hardware. Ensure the mounting surface can support the weight of the light.
- Professional Handling: Installation and servicing should be performed by qualified personnel.
- Cable Management: Route power and DMX cables safely to prevent tripping hazards or damage.
3. Product Overview and Components
The XPCLEOYZ LED Par Light is a compact and powerful lighting fixture. Each unit features 54 individual 3W LEDs (Red, Green, Blue, White) for versatile color mixing. The robust housing and adjustable bracket allow for various mounting options.
Figure 3.1: Front view of a single XPCLEOYZ LED Par Light, showing the 54 RGBW LED array and adjustable mounting bracket.
3.1 Rear Panel and Controls
The rear panel houses the control interface and connection ports.
Figure 3.2: Rear panel of the LED Par Light, featuring the digital display, control buttons, DMX In/Out ports, and power input.
- Digital Display: Shows current mode, DMX address, or parameter values.
- MENU Button: Navigates through the main menu options.
- UP/DOWN Buttons: Adjusts values or scrolls through options within a menu.
- ENTER Button: Confirms selections or saves settings.
- DMX IN/OUT: 3-pin XLR connectors for DMX512 signal input and output.
- POWER IN: Power cable connection.
3.2 Dimensions
Refer to the diagram below for the physical dimensions of the fixture.
Figure 3.3: Product dimensions. Diameter: 22cm, Height (with bracket): 14cm, Depth: 6.5cm.
4. Setup
4.1 Mounting
The fixture can be mounted in various positions using its adjustable bracket. Ensure all mounting hardware is securely fastened and capable of supporting the fixture's weight.
- Floor Mount: Place the fixture on a stable, level surface.
- Truss Mounting: Use appropriate clamps (not included) to attach the bracket to a lighting truss. Always use a safety cable (not included) as a secondary attachment.
- Wall/Ceiling Mount: Secure the bracket to a sturdy wall or ceiling using suitable screws and anchors.
4.2 Power Connection
Connect the provided power cable to the POWER IN port on the rear panel and then to a suitable power outlet. Verify the voltage matches the product specifications.
4.3 DMX Connection (Optional)
For DMX control, connect a DMX cable from your DMX controller's output to the DMX IN port of the first fixture. Then, daisy-chain additional fixtures by connecting the DMX OUT of the first fixture to the DMX IN of the next, and so on. A DMX terminator is recommended for the last fixture in the chain.
5. Operating Instructions
The XPCLEOYZ LED Par Light offers several operating modes, accessible via the rear control panel.
5.1 Control Panel Navigation
- Press MENU to cycle through main menu options (e.g., DMX Address, Auto Mode, Sound Mode, Master/Slave).
- Use UP and DOWN to adjust values or select sub-options.
- Press ENTER to confirm a selection or save a setting.
5.2 Operating Modes
- DMX512 Mode:
This mode allows external control via a DMX controller. Set the DMX address for each fixture using the control panel. Each fixture requires a unique starting address.
Typical DMX Channel Assignments (Example - refer to specific DMX chart for exact details):
Channel Function Value Range 1 Master Dimmer 0-255 (0% - 100%) 2 Red Intensity 0-255 (0% - 100%) 3 Green Intensity 0-255 (0% - 100%) 4 Blue Intensity 0-255 (0% - 100%) 5 White Intensity 0-255 (0% - 100%) 6 Strobe Effect 0-10 (Off), 11-255 (Speed) 7 Program Selection 0-255 (Various Auto Programs) - Auto Mode:
The fixture cycles through pre-programmed light sequences. Use the UP/DOWN buttons to select different auto programs or adjust speed.
Figure 5.1: Examples of individual color outputs from the LED Par Light.
- Sound-Activated Mode:
The lights react to ambient sound. The built-in microphone detects sound, and the light patterns change accordingly. Sensitivity may be adjustable via the control panel.
- Master/Slave Mode:
Connect multiple fixtures via DMX cables. Set one fixture as "Master" and the others as "Slave." The slave units will mimic the master's operation (e.g., Auto Mode, Sound Mode). Ensure the DMX OUT of the master connects to the DMX IN of the first slave, and so on.
Figure 5.2: Multiple LED Par Lights operating in unison, potentially in Master/Slave mode.
6. Maintenance
- Cleaning: Regularly clean the lens and housing with a soft, dry cloth. Do not use abrasive cleaners or solvents. Ensure the fixture is powered off and cooled down before cleaning.
- Inspection: Periodically check power cables, DMX cables, and mounting hardware for any signs of wear or damage. Replace damaged components immediately.
- Storage: When not in use, store the fixture in a dry, dust-free environment, preferably in its original packaging or a padded case to prevent damage.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Fixture does not power on. | No power, faulty cable, or internal issue. | Check power connection and outlet. Test with a different power cable. If problem persists, contact support. |
| No DMX control. | Incorrect DMX address, faulty DMX cable, or DMX controller issue. | Verify DMX address setting. Check DMX cable connections. Ensure DMX controller is functioning correctly. Try a DMX terminator. |
| Lights not syncing in Master/Slave. | Incorrect Master/Slave setting, faulty DMX cable. | Ensure one unit is set to Master and others to Slave. Check DMX daisy-chain connections. |
| High-pitched noise during operation. | Characteristic of some LED drivers, especially at lower brightness levels. | This can be a normal operational characteristic for some units. If the noise is excessive or new, ensure proper ventilation. Consider placement in environments where ambient sound can mask it. |
8. Specifications
- Model: XPCLEOYZ-NO
- Light Source: 54 x 3W RGBW LEDs (Red, Green, Blue, White)
- Total Wattage: 162 Watts (54 x 3W)
- Beam Angle: 26 Degrees
- Control Modes: DMX512, Auto, Sound-Activated, Master/Slave
- DMX Channels: Typically 7 channels (refer to DMX chart for specific model)
- Voltage: 12 Volts (DC)
- Material: Acrylic, Rubber (Housing)
- Item Weight: Approximately 10.04 kg (22.1 lbs) for the 8-pack
- Dimensions (Single Unit): Approximately 22cm (Diameter) x 14cm (Height with bracket) x 6.5cm (Depth)
- Manufacturer: XPC
- First Available: January 6, 2020
9. Warranty and Support
For warranty information and technical support, please refer to the purchase documentation or contact the seller directly. Keep your proof of purchase for any warranty claims.
XPCLEOYZ is committed to providing quality products and customer satisfaction. If you encounter any issues not covered in this manual, please reach out to our support team for assistance.