Important Safety Instructions
Please read and understand all safety instructions before using this heater. Failure to follow these instructions may result in electric shock, fire, or serious injury.
- Always plug heaters directly into a wall outlet/receptacle. Never use with an extension cord or relocatable power tap (outlet/power strip).
- This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces.
- Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9 meters) from the front of the heater and keep them away from the sides and rear.
- Extreme caution is necessary when any heater is used by or near children or invalids and whenever the heater is left operating and unattended.
- Do not operate any heater with a damaged cord or plug or after the heater malfunctions, has been dropped or damaged in any manner.
- Do not use outdoors.
- To disconnect heater, turn controls to OFF, then remove plug from outlet.
- Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage the heater.
- To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use on soft surfaces, like a bed, where openings may become blocked.
- A heater has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint, or flammable liquids are used or stored.
- Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons.
- Always unplug heater when not in use.
Product Overview
The Ikon Oil-Filled Heater IKNW-13C2 is designed to provide efficient and consistent warmth for your indoor spaces. Its 13 fin design maximizes heat distribution.
Image: Front view of the Ikon Oil-Filled Heater IKNW-13C2, showing its 13 fins and control panel.
Components
- Heating Fins: 13 oil-filled fins for heat radiation.
- Control Panel: Includes thermostat dial and power settings.
- Power Cord: For connecting to an electrical outlet.
- Wheels: For easy portability.
- Handle: For moving the heater.
Setup Instructions
1. Unpacking
- Carefully remove the heater from its packaging.
- Remove all packaging materials, including any protective films or foam inserts.
- Inspect the heater for any signs of damage. If damaged, do not use and contact customer support.
2. Wheel Assembly (if required)
Some models may require minor wheel assembly. Refer to the diagrams below for guidance. Ensure wheels are securely attached before use.
3. Placement
- Place the heater on a firm, level surface.
- Ensure the heater is at least 3 feet (0.9 meters) away from walls, furniture, and other combustible materials.
- Do not place the heater directly below a power outlet.
- Avoid placing the heater in high-traffic areas where it could be tripped over.
4. Power Connection
- Ensure the heater is in the "OFF" position before plugging it in.
- Plug the power cord directly into a grounded 220-240V AC electrical outlet. Do not use extension cords or power strips.
Operating Instructions
1. Powering On/Off
- To turn on, rotate the power selector dial to your desired heat setting (e.g., Low, Medium, High).
- To turn off, rotate the power selector dial to the "OFF" position.
2. Temperature Control (Thermostat)
- Rotate the thermostat dial clockwise to increase the desired temperature setting.
- Rotate the thermostat dial counter-clockwise to decrease the desired temperature setting.
- The heater will cycle on and off to maintain the set temperature.
3. Safety Features
- Overheat Protection: The heater is equipped with an automatic overheat protection system that will shut off the unit if it becomes too hot. If this occurs, unplug the heater, allow it to cool for 30 minutes, and then plug it back in.
- Tip-Over Switch: A safety switch automatically turns off the heater if it is accidentally tipped over. Place the heater upright on a flat surface to resume operation.
Maintenance
1. Cleaning
- Always unplug the heater and allow it to cool completely before cleaning.
- Wipe the exterior surfaces with a soft, damp cloth. Do not use abrasive cleaners or solvents.
- Do not immerse the heater in water or allow water to drip into the interior.
- Clean dust from the air intake and exhaust openings with a vacuum cleaner or a soft brush.
2. Storage
- When not in use, store the heater in a cool, dry place.
- It is recommended to store the heater in its original packaging to protect it from dust and damage.
- Wrap the power cord neatly around the cord storage area (if available) or secure it with a tie.
Troubleshooting
Before contacting customer support, please refer to the following table for common issues and solutions.
| Problem | Possible Cause | Solution |
|---|---|---|
| Heater does not turn on. | Not plugged in; power outlet not working; thermostat set too low; overheat protection activated; tip-over switch activated. | Ensure plug is firmly in outlet; check circuit breaker; turn thermostat higher; unplug and allow to cool; place heater upright on a flat surface. |
| Heater produces insufficient heat. | Thermostat set too low; room too large for heater; doors/windows open. | Increase thermostat setting; ensure heater is appropriate for room size; close doors and windows. |
| Heater makes unusual noises. | Normal expansion/contraction of metal; loose component. | Minor clicking/popping is normal. If noise is loud or persistent, discontinue use and contact support. |
| Heater smells burnt or emits smoke. | Dust accumulation; internal fault. | Immediately unplug the heater. Clean dust from vents. If smell/smoke persists, discontinue use and contact support. |
Specifications
| Feature | Detail |
|---|---|
| Brand | Ikon |
| Model Number | IKNW-13C2 |
| Type | Oil-Filled Heater |
| Number of Fins | 13 |
| Wattage | 1000W |
| Power Source | Electric |
| External Product ID | 202002281500 (EAN-13) |
| Manufacturer | Ikon |
| First Available Date | March 2, 2020 |
Warranty Information
This Ikon Oil-Filled Heater IKNW-13C2 comes with a standard manufacturer's warranty. Please refer to the warranty card included in your product packaging for specific terms, conditions, and duration of coverage. Keep your purchase receipt as proof of purchase for warranty claims.
The warranty typically covers defects in materials and workmanship under normal use. It does not cover damage resulting from misuse, accident, alteration, unauthorized repair, or failure to follow the instructions in this manual.
Customer Support
If you have any questions, require assistance, or encounter issues not covered in the troubleshooting section, please contact Ikon customer support.
For the most up-to-date contact information, please visit the official Ikon website or refer to the contact details provided in your product packaging.
When contacting support, please have your model number (IKNW-13C2) and purchase date readily available.
