GENERICO CLIVET HID-P1 Controller User Manual

1. Introduction

This manual provides comprehensive instructions for the installation, operation, and maintenance of the GENERICO CLIVET HID-P1 Controller. This device is designed for managing small rooftop electronic systems and serves as a replacement for the C5110765 model. Please read this manual thoroughly before installation and use to ensure proper function and safety.

2. Safety Information

• Always disconnect power to the system before performing any installation, maintenance, or troubleshooting.
• Installation should only be performed by qualified personnel in accordance with local electrical codes and regulations.
• Do not expose the controller to moisture, extreme temperatures, or corrosive environments.
• Do not attempt to open or repair the unit yourself. Refer all servicing to authorized service personnel.
• Ensure all wiring connections are secure and properly insulated to prevent short circuits.

3. Package Contents

Verify that all items are present in the package:

• GENERICO CLIVET HID-P1 Controller (1 unit)
• Mounting screws (if applicable, check packaging)
• This User Manual

4. Product Overview

The CLIVET HID-P1 is a compact controller designed for intuitive operation of your rooftop electronic system. It features a clear display and tactile buttons for various functions.

Figure 1: Front view of the GENERICO CLIVET HID-P1 Controller. This image shows the device with a blank display, indicating its general appearance and button layout before activation.

Figure 2: Active display and control buttons of the GENERICO CLIVET HID-P1 Controller. The screen displays "NOVARA impianti 3S srl", indicating an operational state. Below the screen are several buttons for system control: temperature adjustment (up/down arrows), fan speed, Eco mode, mode selection (snowflake/sun), and a Clean function, along with a power button.

4.1. Controls and Display

• Display Screen: Shows current settings, operating mode, and system status. (Refer to Figure 2)
• Up/Down Arrows (Temperature): Adjusts temperature settings.
• Fan Icon: Controls fan speed or mode.
• Eco Button: Activates energy-saving mode.
• Mode Button (Snowflake/Sun): Selects heating or cooling mode.
• Clean Button: Initiates a cleaning cycle or function.
• Power Button: Turns the unit on or off.

5. Setup and Installation

Before beginning installation, ensure the main power supply to the rooftop electronic system is disconnected. This controller is designed to replace the C5110765 model.

1. Power Disconnection: Turn off the main power supply to the entire system at the circuit breaker. Verify power is off using a voltage tester.
2. Remove Old Controller: Carefully detach the existing C5110765 controller from its mounting location. Note the wiring connections before disconnecting them. It is recommended to take a photograph of the wiring for reference.
3. Wiring Connections: Connect the wires from the rooftop electronic system to the corresponding terminals on the new GENERICO CLIVET HID-P1 Controller. Ensure all connections are secure and match the previous setup. Refer to the wiring diagram provided with your rooftop electronic system for specific details.
4. Mounting: Mount the new HID-P1 controller securely in the desired location using appropriate screws. Ensure it is level and firmly attached.
5. Power Restoration: Once installation is complete and all connections are verified, restore power to the system at the circuit breaker.
6. Initial Power-Up: The controller should power on and display its initial screen (similar to Figure 2).

Note: If you are unsure about any step, consult a qualified electrician or HVAC technician.

6. Operating Instructions

This section details how to operate your GENERICO CLIVET HID-P1 Controller.

6.1. Power On/Off

• Press the Power Button (red button on the right, as seen in Figure 2) to turn the controller on or off.

6.2. Setting Temperature

• Use the Up Arrow and Down Arrow buttons (leftmost buttons, as seen in Figure 2) to adjust the desired temperature. The current set temperature will be displayed on the screen.

6.3. Selecting Operating Mode

• Press the Mode Button (snowflake/sun icon, as seen in Figure 2) to cycle through available operating modes, such as Cooling (snowflake) or Heating (sun).

6.4. Fan Speed Control

• Press the Fan Icon Button (next to temperature buttons, as seen in Figure 2) to adjust the fan speed or select an automatic fan mode.

6.5. Eco Mode

• Press the Eco Button to activate or deactivate the energy-saving mode. This mode optimizes settings for reduced power consumption.

6.6. Clean Function

• Press the Clean Button to initiate a specific cleaning cycle or function, if supported by the connected rooftop electronic system. Refer to your system's manual for details on this function.

7. Maintenance

Regular maintenance ensures optimal performance and longevity of your controller.

• Cleaning: Wipe the surface of the controller with a soft, dry cloth. For stubborn dirt, use a slightly damp cloth with mild soap, then wipe dry. Do not use abrasive cleaners, solvents, or spray liquids directly onto the unit.
• Inspection: Periodically check the wiring connections for any signs of wear, corrosion, or looseness. Ensure the controller is securely mounted.
• Software Updates: If applicable, refer to the manufacturer's website or your system's documentation for information on potential software updates for the controller.

8. Troubleshooting

This section addresses common issues you might encounter with your HID-P1 controller.

9. Specifications

10. Warranty and Support

For warranty information and technical support, please refer to the documentation provided with your purchase or contact GENERICO customer service. Keep your proof of purchase for warranty claims.

For recycling information regarding this product, please consult local regulations for electronic waste disposal.

Information on handling broken or damaged lamps (if applicable to your connected system) can be found through relevant environmental agencies or product-specific guidelines.