Intex 12' x 30" Metal Frame Swimming Pool with Filter Pump and Maintenance Kit User Manual

1. Introduction

This manual provides essential information for the safe and efficient setup, operation, and maintenance of your Intex 12' x 30" Metal Frame Swimming Pool. Please read all instructions carefully before assembly and use to ensure proper function and safety.

2. Safety Information

WARNING: Failure to follow these instructions can result in serious injury or death.

• Always supervise children in and around the pool.
• Do not dive or jump into the pool. The water depth is not sufficient for diving.
• Ensure the pool is set up on a level surface. Uneven surfaces can cause the pool to collapse.
• Keep electrical cords and equipment away from water.
• Install appropriate barriers around the pool to prevent unsupervised access by children.
• Regularly check all components for wear and tear. Replace damaged parts immediately.

3. Package Contents

Verify that all components listed below are present in your package. If any parts are missing or damaged, do not proceed with assembly and contact customer support.

• Intex 12' x 30" Metal Frame Pool Liner
• Metal Frame Components (horizontal beams, vertical legs, corner joints)
• Intex Filter Pump (Model 28603EG)
• Type "A" Filter Cartridge
• Hoses and Clamps for Filter Pump Connection
• Intex Deluxe Pool Maintenance Kit (includes telescoping pole, vacuum head, skimmer net, wall brush)
• Instruction Manual (this document)

4. Setup

Proper site preparation and assembly are crucial for the stability and longevity of your pool.

4.1 Site Preparation

1. Choose a firm, level area in your yard, free from sharp objects, debris, or loose soil.
2. Ensure the area is large enough to accommodate the pool and allow for safe access around it.
3. Avoid placing the pool under overhead power lines or near trees that may drop leaves and debris.
4. Clear any grass or vegetation from the chosen area. A ground cloth (not included) is recommended to protect the pool liner.

4.2 Pool Assembly

Follow these steps to assemble the metal frame pool. It is recommended to have at least two people for assembly.

1. Unfold the pool liner and spread it out in the prepared area. Ensure the drain plug is facing the desired drainage location.
2. Assemble the horizontal beams by sliding them through the sleeves at the top of the pool liner.
3. Connect the horizontal beams using the corner joints.
4. Insert the vertical legs into the T-joints of the frame. Ensure they are securely seated.
5. Attach the leg caps to the bottom of each vertical leg.

4.3 Filter Pump Connection

Connect the filter pump to the pool as follows:

1. Identify the two openings on the side of the pool liner for the filter pump.
2. Attach the two hoses from the filter pump to these openings using the provided clamps. Ensure all connections are tight to prevent leaks.
3. Place the filter pump on a stable, level surface at least 10 feet away from the pool.

4.4 Filling the Pool

1. Begin filling the pool with water. As the water level rises, smooth out any wrinkles in the bottom of the liner.
2. Fill the pool to the recommended water level, typically indicated by a fill line on the liner or frame.

4.5 Setup Video Guide

For a visual guide on setting up your Intex Metal Frame Pool, please watch the official seller video below:

5. Operating Instructions

The filter pump is essential for keeping your pool water clean and clear.

5.1 Filter Pump Operation

1. Ensure the filter pump is properly connected to the pool and plugged into a grounded electrical outlet.
2. Open the air release valve on top of the filter pump to allow any trapped air to escape. Close it once water begins to flow out.
3. Turn on the filter pump. The pump should run for a minimum of 4-6 hours per day to ensure adequate water circulation and filtration. Adjust run time based on pool usage and water clarity.

6. Maintenance

Regular maintenance is vital for extending the life of your pool and ensuring clean, safe swimming conditions.

6.1 Filter Cartridge Cleaning and Replacement

1. Turn off and unplug the filter pump before performing any maintenance.
2. Unscrew the filter housing cap and remove the Type "A" filter cartridge.
3. Rinse the cartridge thoroughly with a garden hose to remove debris.
4. Replace the cartridge every 2 weeks or sooner if the water flow is reduced or the cartridge appears heavily soiled.

6.2 Water Chemistry

Test your pool water regularly (daily or every other day) using a pool test kit. Maintain the following levels:

• Chlorine: 1-3 ppm (parts per million)
• pH: 7.4-7.6
• Alkalinity: 80-120 ppm

Adjust chemicals as needed according to product instructions.

6.3 Pool Cleaning

Use the included Deluxe Pool Maintenance Kit for routine cleaning:

• Skimming: Use the skimmer net to remove leaves, insects, and other floating debris from the water surface daily.
• Vacuuming: Attach the vacuum head to the telescoping pole and connect it to the filter pump's suction side (refer to pump manual for specific connection). Vacuum the pool bottom to remove settled debris.
• Brushing: Use the wall brush to scrub the pool walls and floor, dislodging algae and dirt for the filter to capture.

6.4 Winterization (Off-Season Storage)

When temperatures drop below 45°F (7°C), it is recommended to drain, clean, and properly store your pool to prevent damage.

1. Drain the pool completely using the drain plug.
2. Clean the liner thoroughly with mild soap and water.
3. Disassemble the frame and allow all components to dry completely.
4. Store the liner and frame parts in a dry, protected area, away from extreme temperatures and pests.

7. Troubleshooting

8. Specifications

9. Warranty and Support

For warranty information, please refer to the documentation included with your product or visit the official Intex website. For technical support, replacement parts, or further assistance, please contact Intex customer service directly. Keep your purchase receipt and model number handy when contacting support.