1. Introduction
This manual provides essential instructions for the installation, operation, and maintenance of your Hormann FCT3-1 BS Wireless Code Switch. This device is designed to control up to three compatible Hormann gate operators using a secure, programmable code. Please read these instructions carefully before use to ensure safe and efficient operation.
2. Safety Instructions
Observe the following safety guidelines to prevent injury or damage to the device:
- Keep the device out of reach of children.
- Do not expose the device to extreme temperatures, direct sunlight, or moisture beyond its specified IP44 rating.
- Only use the specified battery type (2 x 1.5V LR03/AAA). Ensure correct polarity during installation.
- Do not attempt to open or repair the device yourself. Refer all servicing to qualified personnel.
- Ensure the mounting location is secure and stable to prevent the device from falling.
- Always test the functionality of the gate operator after programming the code switch to ensure safe operation.
3. Package Contents
Verify that all items are present in the package:
- 1 x Hormann FCT3-1 BS Wireless Code Switch
- 2 x 1.5V LR03/AAA Batteries
- Instruction Manual (this document)
4. Technical Specifications
| Model | FCT3-1 BS |
| Reference Number | 4511856 |
| Housing Material | Lacquered Plastic |
| Color | Light Grey (RAL 7040) |
| Protection Class | IP 44 |
| Power Supply | 2 x 1.5V LR03/AAA Batteries |
| Dimensions (L x W x H) | 80 x 80 x 30 mm |
| Operating Temperature | -20 °C to +50 °C |
| Frequency | 868 MHz Bi-Secur |
| Control Capacity | Up to 3 Gate Operators |
5. Setup and Installation
5.1 Battery Installation
- Carefully open the battery compartment cover on the back of the code switch.
- Insert the two 1.5V LR03/AAA batteries, ensuring correct polarity (+/-) as indicated inside the compartment.
- Close the battery compartment cover securely.
5.2 Mounting the Code Switch
The FCT3-1 BS is designed for surface mounting. Choose a location that is easily accessible, protected from direct heavy rain (though IP44 rated), and within effective range of your gate operator.
- Mark the desired mounting position on the wall or surface.
- Drill appropriate holes for the mounting screws (screws and wall plugs are typically not included and should be selected based on the mounting surface).
- Secure the code switch to the surface using the appropriate fasteners.
Figure 1: Hormann FCT3-1 BS Wireless Code Switch. This image shows the Hormann FCT3-1 BS Wireless Code Switch. It features a square, light grey housing with a circular keypad in the center. The keypad includes numerical buttons from 0 to 9, a light/bell symbol button, and a key symbol button. The 'Hormann' logo is visible at the bottom of the device.
5.3 Programming with Gate Operator
The FCT3-1 BS must be programmed to your specific Hormann gate operator(s). The exact programming procedure varies depending on your gate operator model. Refer to the instruction manual of your Hormann gate operator for detailed steps on how to pair a new wireless code switch. Generally, this involves:
- Activating the programming mode on your gate operator.
- Entering a desired code on the FCT3-1 BS keypad.
- Confirming the code and transmitting the signal to the operator.
- Testing the functionality.
The FCT3-1 BS supports controlling up to three different gate operators or functions. Each operator/function will require its own unique code and programming sequence.
6. Operating the Code Switch
6.1 Entering a Code
To operate a programmed gate operator:
- Press the numerical keys to enter your pre-programmed code.
- After entering the full code, press the key symbol button (bottom right) to transmit the signal.
- The gate operator should respond according to its programming (e.g., open, close, stop).
6.2 Keypad Illumination
The keypad features illumination for use in low-light conditions. The illumination activates automatically upon pressing any key. It will remain lit for a short period after the last key press.
The light/bell symbol button (bottom left) can be used to activate the illumination without sending a command, or if programmed, to trigger a specific function on your gate operator (e.g., turn on an external light, ring a bell, if supported by your operator).
7. Maintenance
7.1 Battery Replacement
When the batteries are low, the keypad illumination may dim or the transmission range may decrease. Replace the batteries as follows:
- Open the battery compartment cover on the back of the device.
- Remove the old 1.5V LR03/AAA batteries.
- Insert new 1.5V LR03/AAA batteries, observing correct polarity.
- Close the battery compartment cover securely.
Note: Dispose of used batteries according to local regulations.
7.2 Cleaning
Clean the surface of the code switch with a soft, damp cloth. Do not use abrasive cleaners or solvents, as these can damage the housing finish.
7.3 Inspection
Periodically inspect the device for any signs of damage, such as cracks in the housing or loose mounting. Ensure the keypad buttons function correctly.
8. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Keypad does not light up or respond. | Dead or incorrectly installed batteries. | Replace batteries, ensuring correct polarity. |
| Gate operator does not respond to code. | Incorrect code entered; Code switch not programmed to operator; Operator out of range; Signal interference. | Verify the code; Re-program the code switch to the operator (refer to operator manual); Move closer to the operator; Check for sources of interference. |
| Reduced operating range. | Low batteries; Obstructions between code switch and operator; Signal interference. | Replace batteries; Ensure clear line of sight; Identify and remove sources of interference. |
9. Compatible Gate Operators
The Hormann FCT3-1 BS Wireless Code Switch is compatible with the following Hormann gate operator models and series:
- SupraMatic E/P
- SupraMatic HT
- ProMatic
- ProMatic Battery
- RollMatic
- RotaMatic / P / PL
- RotaMatic Solar Battery
- VersaMatic / P
- VersaMatic Solar Battery
- LineaMatic / P
- LineaMatic
Additionally, due to its Bi-Secur technology, it is backward compatible with Hormann drives from Series 1 and 2 (868 MHz).
