1. Introduction
This manual provides essential information for the safe and effective use of your Parmida LED Dual-Head Work Light. Please read these instructions thoroughly before assembly, operation, or maintenance. Retain this manual for future reference.
Figure 1: Parmida LED Dual-Head Work Light with Tripod Stand.
2. Safety Information
Observe the following safety precautions to prevent injury or damage to the product:
- Electrical Safety: Ensure the power cord is UL Approved and in good condition. Do not operate with a damaged cord or plug. Connect to a properly grounded outlet.
- Water Resistance: The light heads are IP65 rated for water resistance, suitable for outdoor use. However, avoid submerging the unit in water. Ensure electrical connections are dry before plugging in.
- Heat: LED lights generate heat. Do not touch the light heads immediately after prolonged use. Allow them to cool.
- Eye Protection: Avoid direct eye exposure to the bright LED light.
- Stability: Always ensure the tripod stand is placed on a stable, level surface to prevent tipping. Do not extend the stand beyond its recommended height if stability is compromised.
- Ventilation: Ensure adequate airflow around the light heads to prevent overheating.
- Children and Pets: Keep the work light out of reach of children and pets.
3. Product Components
The Parmida LED Dual-Head Work Light includes the following main components:
- Dual LED Light Heads (2 units)
- Adjustable Tripod Stand
- Mounting Bracket for Light Heads
- UL Approved Power Cord
- Carry Handle (integrated)
Figure 2: Key features of the Parmida LED Dual-Head Work Light.
4. Setup Instructions
Follow these steps to assemble and set up your work light:
- Unpack Components: Carefully remove all parts from the packaging.
- Extend Tripod Legs: Place the tripod stand on a flat, stable surface. Extend the three legs outwards until they are fully spread and locked into position.
- Adjust Stand Height: Loosen the locking collars on the main pole of the tripod. Extend the pole to the desired height, up to 6 feet (1.8 meters). Securely tighten the locking collars to prevent slippage.
- Attach Light Heads: The dual light heads are pre-attached to a crossbar. This crossbar then attaches to the top of the main tripod pole. Ensure it is securely fastened.
- Position Light Heads: Adjust the angle and rotation of each light head as needed. Each head can rotate 360 degrees and tilt 270 degrees.
- Connect Power: Plug the UL Approved power cord into a suitable 120V AC grounded electrical outlet.
Figure 3: The work light can be configured in various heights and used with detached heads.
4.1 Detaching Light Heads
For portable use or alternative mounting, the light heads can be detached from the tripod stand:
- Unplug the unit from the power source.
- Locate the fastening mechanism that secures the light head crossbar to the tripod pole.
- Carefully detach the light heads. They can then be used independently or placed on other surfaces.
Figure 4: Illustration of multi-use options, including detaching the light heads.
5. Operating Instructions
To operate your Parmida LED Dual-Head Work Light:
- Power On/Off: Each light head has an individual ON/OFF switch located on its housing. Press the switch to turn the light ON or OFF. You can operate one or both lights independently.
- Adjust Light Direction: Loosen the adjustment knobs on the sides of each light head. Pivot the light head to the desired angle (up to 270 degrees tilt) and rotate it horizontally (up to 360 degrees). Tighten the knobs to secure the position.
Figure 5: Demonstrating the full adjustability of the light heads.
Figure 6: The work light providing illumination in a work environment.
6. Maintenance
Regular maintenance ensures optimal performance and longevity of your work light:
- Cleaning: Disconnect the power before cleaning. Use a soft, damp cloth to wipe down the exterior of the light heads and stand. Periodically clean the tempered glass lens to maintain light output and prevent heat buildup from dust accumulation. Do not use abrasive cleaners or solvents.
- Cord Inspection: Regularly inspect the power cord for any signs of damage, cuts, or fraying. If damaged, discontinue use and replace the cord by a qualified technician.
- Storage: When not in use, fold the tripod stand for compact storage. Store the unit in a dry, clean environment away from extreme temperatures.
Figure 7: The work light components arranged for compact storage.
7. Troubleshooting
If you encounter issues with your Parmida LED Dual-Head Work Light, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Light does not turn on | No power supply Faulty power cord Light switch off | Check power outlet and circuit breaker Inspect power cord for damage; replace if necessary Ensure individual light switches are ON |
| Light flickers | Unstable power connection Loose wiring | Ensure power cord is securely plugged in Contact customer support for assistance |
| Light heads become excessively hot | Poor ventilation Dust accumulation on lens/heat sink | Ensure adequate space around light heads Clean lens and heat sink periodically |
| Tripod stand is unstable | Uneven surface Legs not fully extended/locked | Place on a flat, stable surface Ensure all legs are fully extended and locking mechanisms are engaged |
8. Specifications
Detailed technical specifications for the Parmida LED Dual-Head Work Light:
| Feature | Specification |
|---|---|
| Model Number | PLED-DHWL100W-OR |
| Power Consumption | 200W (100W per head) |
| Luminous Flux | 20,000 Lumens (10,000 Lumens per head) |
| Input Voltage | 120V AC |
| Color Temperature | 5000K |
| Ingress Protection (IP) Rating | IP65 (Water Resistant) |
| Material | Durable Die-Cast Aluminum Body, Tempered Glass Lens |
| Adjustable Height | Up to 6 feet (1.8 meters) |
| Cord Length | 8 feet |
| Estimated Lifespan | 30,000 hours |
| Product Dimensions (Extended) | 24.6"L x 24.6"W x 66.9"H |
| Item Weight | 9.08 pounds (4.13 kg) |
Figure 8: Visual representation of key product specifications and dimensions.
9. Warranty and Support
Parmida LED Technologies stands behind the quality of its products.
- Warranty: This product is covered by a 5-Year Warranty from the date of purchase. This warranty covers defects in materials and workmanship under normal use.
- Customer Service: For warranty claims, technical assistance, or any questions regarding your Parmida LED Dual-Head Work Light, please contact our dedicated in-house Customer Service team. Refer to the product packaging or the Parmida LED Technologies website for current contact information.