Ecolink ZigBee Wireless Flood Detection Sensor FLZB1-ECO User Manual

1. Introduction

The Ecolink ZigBee Wireless Flood Detection Sensor (Model FLZB1-ECO) is designed to provide early warning of water leaks and potential flooding in your home or property. This sensor utilizes ZigBee technology to communicate with compatible smart home hubs, such as Samsung SmartThings, alerting you to the presence of water before significant damage occurs. Its slim design allows for discreet placement in various locations where water leaks are a concern.

Image: The Ecolink ZigBee Wireless Flood Detection Sensor is designed to detect water leaks from the first drop in your home.

2. Features

• Water Detection: Detects floods with as little as 1/64" of water.
• Slim Design: A thin profile of 0.39" allows for placement under appliances and in tight spaces.
• Durable Probes: Equipped with 4 gold-plated and corrosion-resistant probes for reliable water detection.
• Long Battery Life: Designed for extended operation, offering up to 4 years of battery life under typical usage conditions.
• Compatibility: Manufacturer tested to be compatible with Samsung SmartThings.
• Easy Installation: Includes an optional mounting bracket for flexible placement.

Image: Key features of the Ecolink Zigbee Flood Sensor, including detection capability, slim design, and compatibility.

3. Setup

3.1. Battery Installation

The sensor requires one (1) CR123A battery, which is included. To install or replace the battery:

1. Gently twist the top and bottom halves of the sensor to separate them.
2. Insert the CR123A battery into the battery compartment, ensuring correct polarity (+/-).
3. Align the halves and twist them back together until securely closed.

3.2. Pairing with a Smart Home Hub

The Ecolink FLZB1-ECO sensor uses ZigBee protocol for communication. Follow these general steps to pair it with your compatible smart home hub (e.g., Samsung SmartThings):

1. Place your smart home hub into pairing or discovery mode. Refer to your hub's specific instructions for this process.
2. With the battery installed, the sensor should automatically attempt to join the ZigBee network. Some hubs may require you to press a button on the sensor (if available) or trigger it (e.g., by briefly touching the probes with a wet cloth) to initiate pairing.
3. Once successfully paired, the hub's application should confirm the addition of the new device.

3.3. Sensor Placement

Strategic placement is crucial for effective flood detection. Consider areas prone to water leaks:

• Under sinks (kitchen, bathroom)
• Near water heaters
• Behind toilets
• Under washing machines or dishwashers
• In basements or utility rooms

Place the sensor on a flat surface where water would first accumulate. The gold-plated probes on the bottom of the device must be in direct contact with any pooling water for detection.

Image: The Ecolink Zigbee Wireless Flood Detection Sensor mounted to a flat surface to detect the presence of water.

4. Operating Instructions

Once installed and paired, the Ecolink FLZB1-ECO sensor operates automatically. When the four gold-plated probes on the bottom of the sensor come into contact with water, the device will detect the presence of moisture.

Within approximately 2 seconds of detecting water, the sensor will transmit an alarm signal to your connected smart home hub. Your hub will then execute any pre-configured actions, such as sending notifications to your smartphone, triggering other smart devices, or activating an audible alarm, depending on your system's setup.

To test the sensor, carefully place it on a damp cloth or a small amount of water. The sensor should trigger an alert through your smart home system. Remove the sensor from the water and dry the probes thoroughly after testing.

5. Maintenance

5.1. Battery Replacement

The sensor is designed for long battery life. When the battery level becomes low, your smart home hub should notify you. Replace the battery as described in Section 3.1. Use only CR123A batteries for optimal performance.

5.2. Cleaning

Periodically inspect the sensor, especially the probes, for any dirt, dust, or corrosion. Clean the sensor with a soft, dry cloth. Do not use abrasive cleaners or immerse the sensor in water.

5.3. Regular Testing

It is recommended to test the sensor periodically (e.g., monthly or quarterly) to ensure it is functioning correctly. Follow the testing procedure outlined in Section 4.

6. Troubleshooting

• Sensor not pairing:
  • Ensure the sensor is within range of your ZigBee hub.
  • Verify the battery is correctly installed and has sufficient charge.
  • Put your hub into pairing mode again and try re-initiating the sensor's pairing process.
  • If issues persist, try resetting the sensor (refer to manufacturer's specific reset instructions, if available, or remove and reinsert battery).
• No alerts when water is detected:
  • Check the sensor's battery level in your smart home app.
  • Ensure the sensor is still connected to your hub.
  • Verify that your smart home app's notification settings for the sensor are correctly configured.
  • Clean the sensor probes to ensure no debris is preventing proper contact with water.
• False alarms:
  • Ensure the sensor is placed on a dry, stable surface.
  • Check for condensation or high humidity in the area that might be triggering the sensor.
  • Inspect the probes for any residue or damage.

7. Specifications

8. Warranty Information

For detailed warranty information regarding your Ecolink ZigBee Wireless Flood Detection Sensor, please refer to the documentation provided with your purchase or visit the official Ecolink website. Warranty terms typically cover manufacturing defects for a specified period from the date of purchase.

9. Support

If you require technical assistance or have questions not covered in this manual, please contact Ecolink customer support. You can typically find contact information, including phone numbers and email addresses, on the official Ecolink website or in the product packaging.

Ecolink Official Website: www.ecolink.com