Introduction
This manual provides essential information for the installation, operation, maintenance, and troubleshooting of your UpStart Components 21001906 Washer Drain Pump. This replacement part is designed for compatibility with specific Maytag washing machine models, including MAV5057AWW, and replaces part number WP35-6465. Please read these instructions carefully before proceeding with installation or any maintenance.
Image: UpStart Components 21001906 Washer Drain Pump, top-down view showing the pulley and mounting plate.
Safety Information
WARNING: Always disconnect power to the washing machine before attempting any installation, repair, or maintenance. Failure to do so can result in serious injury or electrical shock. If you are unsure about any step, it is recommended to consult a qualified appliance technician.
- Ensure the washing machine is unplugged from the electrical outlet.
- Turn off the water supply to the washing machine.
- Wear appropriate personal protective equipment, such as gloves and safety glasses.
- Be aware of sharp edges and potential water spills during the process.
Installation Instructions
This replacement drain pump is designed for easy at-home installation. However, proper identification of the part and careful execution of steps are crucial. Always compare the new part with your original part to confirm compatibility before installation.
- Prepare the Washer:
Disconnect the washing machine from its power source by unplugging it. Turn off the hot and cold water supply valves. Move the washer away from the wall to access the rear and bottom.
- Drain Residual Water:
Place towels and a shallow pan or bucket under the drain hose and pump area. Disconnect the drain hose from the standpipe or utility sink and allow any remaining water to drain. You may need to tilt the washer slightly to access the pump.
- Locate the Drain Pump:
Depending on your Maytag model, the drain pump is typically located at the bottom front or rear of the washing machine. You may need to remove the front panel or tilt the washer back to access it.
Image: Side view of the UpStart Components 21001906 Washer Drain Pump, showing the motor housing and outlet hose connection.
- Disconnect Hoses and Wiring:
Carefully disconnect the inlet and outlet hoses from the old drain pump. Use pliers to release hose clamps if necessary. Disconnect any electrical wiring connected to the pump. Take a photo before disconnecting to aid reassembly.
Image: Close-up view of the impeller housing of the UpStart Components 21001906 Washer Drain Pump.
- Remove the Old Pump:
Unscrew or unclip the old drain pump from its mounting bracket. Note its orientation for correct installation of the new pump.
- Install the New Pump:
Position the new UpStart Components 21001906 drain pump in the same orientation as the old one. Secure it to the mounting bracket using the original screws or clips.
Image: Bottom view of the UpStart Components 21001906 Washer Drain Pump, showing the water inlet and outlet ports.
- Reconnect Hoses and Wiring:
Attach the inlet and outlet hoses to the new pump, securing them with hose clamps. Reconnect the electrical wiring, ensuring all connections are snug and correct. Refer to your photo if needed.
Image: Top view of the UpStart Components 21001906 Washer Drain Pump, highlighting the pulley mechanism.
- Test the Washer:
Return the washer to its original position. Reconnect the water supply and turn on the valves. Plug the washer back into the electrical outlet. Run a short cycle to check for leaks and proper draining function.
Operating Principles
The drain pump is an integral component of your washing machine's drainage system. It is designed to automatically activate during the spin and drain cycles to remove water from the wash tub. When the washer signals for water removal, the pump's motor engages, causing the impeller to spin and force water out through the drain hose. This process is fully automated and requires no manual intervention during normal operation.
Maintenance
While the drain pump itself requires minimal maintenance, regular care of your washing machine can extend its lifespan and prevent issues with the pump.
- Check for Obstructions: Periodically inspect the drain pump filter (if your washer has one) and the drain hose for lint, small objects, or debris that could clog the pump.
- Avoid Overloading: Overloading the washer can strain the pump and other components.
- Use Proper Detergent: Use only high-efficiency (HE) detergent in HE washers to prevent excessive suds that can interfere with draining.
- Inspect Hoses: Regularly check the drain and fill hoses for cracks, leaks, or blockages.
Troubleshooting
If your washing machine is experiencing drainage issues, the drain pump may be a factor. Here are some common problems and potential solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Washer not draining water. | Clogged drain pump filter, kinked drain hose, faulty drain pump, electrical issue. | Check and clean the drain pump filter. Ensure the drain hose is not kinked or blocked. Verify electrical connections to the pump. If these steps do not resolve the issue, the pump may need replacement. |
| Loud noise during drain cycle. | Debris in the pump impeller, worn pump bearings. | Disconnect power and inspect the pump impeller for foreign objects. If the noise persists and no debris is found, the pump may be failing and require replacement. |
| Water leaking from pump area. | Loose hose connections, cracked pump housing, worn seals. | Tighten hose clamps. Inspect the pump housing for cracks. If the pump itself is leaking, it needs to be replaced. |
If troubleshooting steps do not resolve the issue, professional assistance may be required.
Specifications
| Product Name | UpStart Components 21001906 Washer Drain Pump |
| Model Number | AP-WP35-6465-DL20 |
| Compatible Part Numbers | WP35-6465, AP6008659, 35-6465, 21001589, 21001732, 21001906, 35-2057, 35-2099, 35-3834, 35-5766, 35-6016, PS11741799, WP35-6465VP |
| Power Source | AC/DC |
| Manufacturer | UpStart Components |
Warranty and Support
This UpStart Components replacement part is not an OEM product. Any warranties for this product are offered solely by UpStart Components. For specific warranty details or technical support, please contact UpStart Components directly through their official channels. Please note that this product is not affiliated with any original equipment manufacturer brands, and their warranties do not cover this replacement part.
For further assistance, please refer to the contact information provided by UpStart Components at the time of purchase or on their official website.