User Manual: Floor-Standing Back-to-Wall Sanitary Ware

1. Introduction

This manual provides comprehensive instructions for the installation, operation, and maintenance of your new Generico Floor-Standing Back-to-Wall Sanitary Ware set. This set includes a toilet and a bidet, both designed for modern bathrooms with a focus on hygiene and ease of cleaning.

The ceramic features an advanced easy-clean treatment and a rimless flush system, ensuring efficient water flow and simplified cleaning. The GLAZING COATING applied during the firing process prevents dirt and limescale buildup, making the surfaces exceptionally smooth and easy to maintain.

2. Features

• Floor-standing back-to-wall toilet with rimless flush system (56x35.5x40 cm).
• Floor-standing back-to-wall bidet (54x36x40 cm).
• Soft-close toilet seat made of thermosetting material.
• Rimless design for enhanced hygiene and easier cleaning.
• High-quality ceramic construction.
• Glossy white finish.
• GLAZING COATING for easy-clean surfaces, preventing dirt and limescale buildup.

Figure 2.1: Overview of the Generico Floor-Standing Back-to-Wall Sanitary Ware set in a modern bathroom setting.

3. Safety Information

Please read all safety instructions carefully before installation and use. Failure to follow these instructions may result in property damage or personal injury.

• Always turn off the main water supply before beginning any plumbing work.
• Ensure all connections are watertight to prevent leaks.
• Handle ceramic items with care to avoid chipping or breakage.
• Use appropriate tools and protective gear during installation.
• If you are unsure about any step, consult a qualified plumber.
• Keep small parts out of reach of children.

4. Package Contents

Verify that all components are present and undamaged before proceeding with installation.

• 1 x Floor-standing back-to-wall toilet bowl
• 1 x Floor-standing back-to-wall bidet
• 1 x Soft-close toilet seat with mounting hardware
• Installation hardware (e.g., floor fixings, seals) - may vary by package

5. Setup and Installation

This sanitary ware set is designed for floor-standing, back-to-wall installation. Ensure your plumbing connections are prepared according to local building codes.

5.1. Dimensions and Technical Drawing

Figure 5.1: Detailed technical drawing showing dimensions for the toilet (MODEL NO.: BWT040) and bidet (MODEL NO.: BWT040B). Please refer to these measurements for accurate installation planning.

5.2. Installation Steps (General Guide)

1. Prepare the Area: Ensure the floor is level and clean. Mark the positions for the toilet and bidet according to the technical drawing and your plumbing outlets.
2. Connect Water Supply (Bidet): Connect the hot and cold water supply lines to the bidet mixer (not included). Ensure all connections are sealed properly.
3. Connect Waste Outlet (Bidet): Connect the bidet waste outlet to your drainage system.
4. Secure Bidet: Position the bidet and secure it to the floor using the provided fixings. Ensure it is stable and level.
5. Connect Water Supply (Toilet): Connect the water supply line to the toilet cistern inlet.
6. Connect Waste Outlet (Toilet): Connect the toilet waste outlet to your drainage system. Ensure a tight, leak-proof seal.
7. Secure Toilet: Position the toilet against the wall and secure it to the floor using the provided fixings. Ensure it is stable and level.
8. Install Toilet Seat: Attach the soft-close toilet seat to the toilet bowl according to the seat's specific instructions.
9. Test: Slowly turn on the main water supply and check for any leaks. Flush the toilet and test the bidet to ensure proper function.

Figure 5.2: Example of the installed toilet and bidet set, showcasing its back-to-wall design.

6. Operating Instructions

6.1. Toilet Operation

To flush the toilet, press the flush button on your cistern. The rimless design ensures an efficient and hygienic rinse of the bowl with reduced water consumption.

6.2. Bidet Operation

Operate the bidet using the mixer tap (not included) to control water flow and temperature. Ensure the bidet waste is clear for proper drainage.

6.3. Soft-Close Seat

The toilet seat features a soft-close mechanism. Simply push the seat or lid down gently, and it will close slowly and quietly on its own, preventing slamming and extending product life.

7. Maintenance and Cleaning

Thanks to the GLAZING COATING and rimless design, your sanitary ware is exceptionally easy to clean and maintain.

• Daily Cleaning: Wipe surfaces with a soft cloth and mild, non-abrasive bathroom cleaner. The smooth, non-porous surface prevents dirt and limescale from adhering, making cleaning effortless.
• Rimless Design: The absence of a rim means there are no hidden areas for dirt and bacteria to accumulate. The entire inner bowl is accessible for thorough cleaning.
• Avoid Harsh Chemicals: Do not use abrasive cleaners, scouring pads, or strong chemical detergents, as these can damage the ceramic glaze and the soft-close mechanism.
• Seat Care: Clean the soft-close seat with a damp cloth and mild soap. Avoid excessive force when cleaning the hinges.
• Regular Checks: Periodically check all water connections for leaks and ensure the floor fixings remain secure.

Figure 7.1: Top view of the toilet and bidet, illustrating the ease of access for cleaning due to the rimless design.

8. Troubleshooting

This section addresses common issues you might encounter. For problems not listed here, please contact customer support.

9. Specifications

10. Warranty and Support

For warranty information, please refer to the terms and conditions provided at the time of purchase or contact your retailer. For technical support or replacement parts, please reach out to Generico customer service through your point of purchase.

Please retain your proof of purchase for any warranty claims.