EPEVER Tracer8415AN

EPEVER 80A MPPT Solar Charge Controller User Manual

Model: Tracer8415AN

Brand: EPEVER

1. Introduction

The EPEVER 80A MPPT Solar Charge Controller (Tracer8415AN) is designed to efficiently manage power flow from your solar panels to your battery bank. Utilizing advanced Maximum Power Point Tracking (MPPT) technology, it ensures optimal energy harvesting and extends battery lifespan through intelligent charging algorithms. This manual provides essential information for the proper installation, operation, and maintenance of your solar charge controller.

2. Product Features

  • Advanced MPPT technology with ultra-fast tracking speed, ensuring tracking efficiency no less than 99.5%.
  • High-quality components from ST and Infineon for enhanced product longevity and low failure rates.
  • Adaptive three-stage charging mode based on digital control circuit, prolonging battery life and improving system performance.
  • Integrated load, utility, or generator auto-control relays for easy hybrid power system composition.
  • Comprehensive electronic protections, including overcharging, over-discharging, and PV reverse polarity protection, for safer and more reliable operation.
  • Battery temperature compensation function, real-time energy recording, and statistical functions.
  • Automatic over-temperature power reduction function and 100% full load operation within the working environment temperature range.
  • Wide range of maximum power point operating voltage to improve photovoltaic module utilization.
  • Rated charging power and charging current double automatic limiting function.
  • Supports four charging options: Sealed, Gel, Flooded, and User-defined.
  • Isolated RS485 interface with standard MODBUS communication protocol and 5V power supply for expanded application.
  • Supports up to 8 units in parallel for system expansion and diverse monitoring requirements, suitable for solar RVs, household systems, and field monitoring.

3. Setup and Installation

Proper installation is crucial for the safe and efficient operation of your EPEVER MPPT Solar Charge Controller. Please follow these guidelines carefully.

3.1 Component Identification

EPEVER MPPT Solar Charge Controller with labeled components including PV Terminals, Battery Terminals, Load control relay, RBVS Port, Generator relay ON/OFF, Fuse, RS485 port, RTS Port, Generator and load relay enable, Grounding Terminal, and PV reverse polarity alarm indicator.
Figure 1: Product Features and Component Layout. This image highlights the various terminals and ports on the solar charge controller, including connections for PV input, battery, load, and communication interfaces like RS485 and RTS.
EPEVER MPPT Solar Charge Controller showing the LCD display and various connection points. The image details the Load control relay, Remote voltage sensor, Diesel generator relay ON/OFF, RS485 ports, Remote temperature sensor, Load control relay, and PV reverse polarity alarm.
Figure 2: Detailed View of LCD and Connection Points. This image provides a closer look at the LCD screen and the various input/output terminals, including specific relays and sensor connections.

3.2 Wiring Diagram

Wiring diagram for EPEVER MPPT Solar Charge Controller showing connections to solar panel, battery, inverter, computer, speaker, TV, fan, and load (washing machine).
Figure 3: System Wiring Diagram. This diagram illustrates how to connect the solar charge controller to a solar panel, battery, inverter, and various loads such as a computer, speakers, TV, fan, and washing machine, demonstrating a complete solar power system setup.

Ensure all connections are secure and correctly polarized. Follow the recommended connection order: first connect the battery, then the solar panel, and finally the load. For disconnection, reverse the order: first disconnect the load, then the solar panel, and finally the battery.

3.3 Installation Video Guide

Watch this official video for a step-by-step guide on unboxing and installing your EPEVER MPPT Solar Charge Controller.

Video 1: Unboxing and Installation Guide for Tracer-AN Series MPPT Solar Charge Controller. This video demonstrates the unboxing process, identification of components, and the correct steps for connecting the controller to the battery, solar panel, and other accessories, including the MT50 remote meter.

4. Operating Instructions

The LCD display and control buttons allow for easy monitoring and configuration of the charge controller.

4.1 LCD Display Navigation

Use the "SELECT" button to cycle through different display interfaces (e.g., battery voltage, PV voltage, load status). Use the "ENTER" button to confirm selections or enter setting modes.

4.2 Battery Type Setting

To set the battery type:

  1. Navigate to the Battery Voltage interface on the LCD.
  2. Long press the "ENTER" button to enter the battery type setting interface.
  3. Use the "SELECT" button to choose your battery type (Sealed, Gel, Flooded, or User).
  4. After choosing, wait for 5 seconds or press the "ENTER" button again to successfully modify and save the setting.

4.3 Load Working Mode Setting

The controller offers various load working modes to suit different application needs. Refer to the table below for available modes and their descriptions.

Table showing Load Working Modes for Timer 1 and Timer 2, including Light ON/OFF, and various timed load operations relative to sunset and sunrise.
Figure 4: Load Working Mode Table. This table details various load control options, including light-sensitive modes (Light ON/OFF) and timed operations relative to sunset and sunrise, allowing users to configure automatic load management.

5. Maintenance

To ensure the long-term performance and safety of your EPEVER solar charge controller, regular maintenance is recommended:

  • Clean Terminals: Periodically check and clean all terminals to ensure tight connections and prevent corrosion.
  • Inspect Wiring: Verify that all wiring is intact, free from damage, and properly secured.
  • Check Ventilation: Ensure the controller's heat sink and ventilation openings are free from dust and debris to maintain proper cooling.
  • Monitor Performance: Regularly check the LCD display for any error codes or unusual readings. Compare actual performance with expected values.
  • Battery Health: Monitor battery voltage and temperature to ensure they are within optimal operating ranges.

6. Troubleshooting

If you encounter issues with your solar charge controller, refer to the following common troubleshooting steps:

  • No Display/Power: Check battery connections and ensure the battery voltage is within the controller's operating range. Verify the fuse is intact.
  • No Charging: Ensure solar panels are connected correctly and receiving sufficient sunlight. Check PV voltage on the display. Verify battery type settings are correct.
  • Load Not Working: Check load connections and ensure the load current does not exceed the controller's rating. Verify load working mode settings.
  • Over-temperature Alarm: Ensure the controller has adequate ventilation and is not installed in an enclosed space without airflow. Reduce load if necessary.
  • Error Codes: Consult the detailed error code section in the full product manual (available on the EPEVER website) for specific error interpretations and solutions.

7. Specifications

SpecificationValue
Model NumberTracer8415AN
BrandEPEVER
Nominal System Voltage12V/24V/36V/48V DC Auto
Max. PV Open Circuit Voltage150V
Rated Charge Current80A
Rated Charge Power (12V/24V/36V/48V)1000W/12V, 2000W/24V, 3000W/36V, 4000W/48V
Battery Type SupportSealed, Gel, Flooded, User
Tracking Efficiency≥99.5%
Max. Conversion Efficiency98.50%
Full Load Efficiency98.00%
RS485 InterfaceYes (RJ45)
EnclosureIP20
Item Weight15.57 pounds
Package Dimensions19.2 x 12.5 x 8.5 inches
Table of technical parameters for Tracer5415AN, Tracer6415AN, Tracer8415AN, and Tracer10415AN models, detailing Nominal System Voltage, Battery Input Voltage Range, Battery Type, Battery Fuse, Rated Charge Current, Rated Charge Power, Max. PV Open Circuit Voltage, MPP Voltage Range, Tracking Efficiency, Max. Conversion Efficiency, Full Load Efficiency, Temperature Compensate Coefficient, Self-Consumption, Grounding, Relay, RS485 Interface, LCD Backlight Time, Ambient Temperature Range, Mounting Hole Size, and Enclosure.
Figure 5: Detailed Technical Parameters. This table provides comprehensive specifications for various models in the Tracer AN series, including the Tracer8415AN, covering electrical characteristics, environmental conditions, and physical dimensions.
Diagram showing the dimensions of the EPEVER MPPT Solar Charge Controller: 134 mm height, 394 mm length, and 240 mm width.
Figure 6: Product Dimensions. This diagram illustrates the physical dimensions of the solar charge controller, providing measurements for height, length, and width.

8. Accessories and Monitoring Options

The EPEVER Tracer AN series controllers support various accessories for enhanced monitoring and control.

Diagram showing various accessories for the EPEVER MPPT Solar Charge Controller, including Remote Temperature Sensor, USB to RS485 cable, OTG cable, Remote Meter (MT50), WiFi Serial Adapter (eBox-WiFi-01), RS485 to Bluetooth Adapter (eBox-BLE-01), and Logger (eLOG01), with connections to MT50, Mobile APP, and PC.
Figure 7: Accessories and Monitoring Options. This diagram illustrates the various accessories compatible with the controller, such as remote meters, communication adapters (WiFi, Bluetooth), and data loggers, enabling comprehensive monitoring via mobile apps or PC software.
  • Remote Temperature Sensor (RTS300R47K3.81A): For accurate battery temperature compensation.
  • USB to RS485 Cable (CC-USB-RS485-150U): Connects the controller to a PC for monitoring via Solar Station PC software.
  • OTG Cable (OTG-12CM): Used with mobile communication cable to achieve real-time monitoring and parameter modification via mobile APP.
  • Remote Meter (MT50): Displays operating data and fault information.
  • WiFi Serial Adapter (eBox-WiFi-01): Enables monitoring via mobile APP software through WiFi signals.
  • RS485 to Bluetooth Adapter (eBox-BLE-01): Enables monitoring via mobile APP software through Bluetooth signals.
  • Logger (eLOG01): Records operating data and real-time status of the controller.

9. Warranty and Support

EPEVER products are designed for reliability and performance. For warranty information, technical support, or service inquiries, please refer to the official EPEVER website or contact their customer service directly. Keep your purchase receipt as proof of purchase for warranty claims.

For more information and resources, visit the official EPEVER Store on Amazon.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.