OSRAM P-VIP TV Lamp Assembly User Manual

1. Introduction

This manual provides essential information for the safe and effective installation, operation, and maintenance of your OSRAM P-VIP TV Lamp Assembly. This high-quality replacement lamp is designed to restore optimal picture brightness and clarity to compatible Mitsubishi rear projection televisions.

Please read this manual thoroughly before attempting any installation or maintenance procedures. Keep this manual for future reference.

Figure 1.1: Front view of the OSRAM P-VIP TV Lamp Assembly. This image shows the complete lamp module, including the bulb and its housing, ready for installation.

2. Important Safety Information

WARNING: Risk of Electric Shock, Burns, and Mercury Exposure.

• Always unplug the television from the power outlet and allow it to cool down completely (at least 30 minutes) before attempting to replace the lamp. Lamps operate at high temperatures and can cause severe burns.
• Do not touch the bare lamp bulb with your fingers. Oils from your skin can create hot spots on the bulb, leading to premature failure. Handle the lamp assembly by its plastic housing.
• Wear protective gloves and eye protection during installation to prevent injury from broken glass.
• This lamp contains mercury. In case of lamp breakage, avoid direct contact with broken glass or mercury. Ventilate the room and follow local regulations for proper disposal of mercury-containing products. Do not dispose of with regular household waste.
• Replace with the same type number. Using an incorrect lamp type can damage your television or pose a safety hazard.
• Do not turn the cartridge over during installation or removal.

Figure 2.1: Top view of the lamp assembly housing, showing caution labels for hot surface and mercury content. Always observe these warnings.

3. Compatibility

This OSRAM P-VIP TV Lamp Assembly is a direct replacement for the following Mitsubishi TV lamp models:

• Mitsubishi 915B455011
• Mitsubishi 915B455012
• Other Mitsubishi Model Series requiring the 82009 lamp assembly.

Please verify your TV's required lamp model number before purchase and installation to ensure compatibility.

4. Installation Instructions

Follow these steps carefully to replace your TV lamp. Refer to your television's owner's manual for specific instructions regarding lamp access and removal, as procedures may vary by model.

1. Prepare the TV:
   • Turn off your Mitsubishi TV.
   • Unplug the TV's power cord from the wall outlet.
   • Allow the TV and the old lamp to cool down for at least 30 minutes. The lamp operates at very high temperatures.
2. Locate the Lamp Access Panel:

   The lamp access panel is typically located on the back or side of the TV. It may be secured with screws. Consult your TV's manual if you cannot locate it.

3. Remove the Old Lamp:
   • Carefully remove the screws securing the lamp access panel.
   • Open or remove the panel.
   • Locate the lamp assembly. It is usually secured by one or more screws or a latch.
   • Loosen any retaining screws or release the latch.
   • Gently pull the old lamp assembly straight out of its compartment. Do not force it.
   • Place the old lamp assembly in a protective bag for proper disposal.
   

   Figure 4.1: Side view of the lamp assembly, showing the handle for easy removal and insertion.

4. Install the New Lamp:
   • Unpack the new OSRAM P-VIP TV Lamp Assembly. Handle it by the plastic housing only.
   • Align the new lamp assembly with the lamp compartment.
   • Gently slide the new lamp assembly straight into the compartment until it is fully seated. Ensure it clicks into place or aligns with the screw holes.
   • Secure the lamp assembly with the retaining screws or latch that were removed earlier. Do not overtighten.
   

   Figure 4.2: Close-up view of the P-VIP bulb within its housing. Ensure the bulb is securely seated before installation.

5. Close the Access Panel:
   • Replace the lamp access panel and secure it with its screws.
   • Ensure all panels are properly closed before proceeding.
6. Power On and Reset Lamp Timer:
   • Plug the TV's power cord back into the wall outlet.
   • Turn on the TV.
   • Consult your TV's owner's manual for instructions on how to reset the lamp timer. Resetting the timer is crucial for accurate lamp life monitoring.

5. Operating the Lamp

Once installed, the OSRAM P-VIP TV Lamp Assembly operates automatically with your television. The lamp will illuminate when the TV is powered on and extinguish when the TV is powered off or enters standby mode.

• Warm-up Time: The lamp may require a short warm-up period (a few seconds to a minute) to reach full brightness after being turned on.
• Cool-down Time: After turning off the TV, the internal cooling fan will continue to run for a short period to cool the lamp. Do not unplug the TV during this cool-down cycle, as it can shorten lamp life.

6. Maintenance and Care

Proper care can help extend the life of your lamp and maintain optimal picture quality.

• Avoid Frequent On/Off Cycles: Repeatedly turning the TV on and off in short intervals can reduce lamp life.
• Ensure Proper Ventilation: Do not block the ventilation openings on your TV. Adequate airflow is essential for lamp cooling.
• Clean Air Filters (if applicable): Some TVs have air filters that should be cleaned periodically to ensure proper cooling. Refer to your TV's manual.
• Handle with Care: Always handle the lamp assembly by its plastic housing. Avoid touching the glass bulb.

7. Troubleshooting

If you experience issues after installing your new lamp, consider the following common solutions:

If these steps do not resolve the issue, please contact OSRAM customer support or a qualified service technician.

8. Product Specifications

9. Warranty Information

This OSRAM P-VIP TV Lamp Assembly is backed by a 1-Year Manufacturer's Warranty. This warranty covers defects in materials and workmanship under normal use. Please retain your proof of purchase for warranty claims.

For detailed warranty terms and conditions, please refer to the official OSRAM website or contact customer support.

10. Customer Support and Authenticity

For technical assistance, troubleshooting, or warranty inquiries, please contact OSRAM customer support through their official channels.

To verify the authenticity of your OSRAM P-VIP lamp, utilize the official "Authenticity Checker" tool available online at OSRAM-ShopYourLight. OSRAM works closely with projector OEMs to ensure bright, crisp, and long-lasting lamp performance.