FLYSKY FS-i6X 10CH 2.4GHz AFHDS2A RC Transmitter Controller User Manual

1. Introduction

This manual provides detailed instructions for the setup, operation, and maintenance of your FLYSKY FS-i6X 10CH 2.4GHz AFHDS2A RC Transmitter Controller and FS-iA10B Receiver. This system is designed for various RC models including fixed-wing aircraft, gliders, helicopters, and quadcopters. The FS-i6X system utilizes multi-channel hopping frequency technology (AFHDS 2A) for reduced interference and features a high-efficiency omni-directional gain antenna for a strong, reliable connection. It also boasts low power consumption, extending battery life, and supports bidirectional communication for telemetry data.

2. Safety Information

Always operate your RC equipment responsibly and safely. Failure to do so may result in injury or damage to property. Please observe the following safety guidelines:

• Ensure all connections are secure before operation.
• Do not operate the transmitter with low battery voltage.
• Keep the transmitter and receiver away from moisture and extreme temperatures.
• Always turn on the transmitter first, then the receiver. When powering off, turn off the receiver first, then the transmitter.
• Regularly inspect all components for signs of wear or damage.
• Operate RC models in open areas, away from people, animals, and obstacles.

3. Package Contents

Verify that all items listed below are included in your package:

• 1X Flysky FS-i6X Transmitter
• 1X FS-iA10B Receiver
• 1X Bind plug
• 1X Upgrade Cable

Note: Batteries are not included and must be purchased separately.

4. Product Overview

The FLYSKY FS-i6X is a 10-channel 2.4GHz RC transmitter designed for precise control of various RC models. It features a clear STNTransflective LCD display for easy navigation and setup.

Figure 4.1: FLYSKY FS-i6X Transmitter and FS-iA10B Receiver included in the package.

4.1 FS-i6X Transmitter

The FS-i6X transmitter features dual antennas for enhanced signal reliability and a robust design suitable for various RC applications. It operates on 6V DC using 4 AA batteries.

Figure 4.2: Front view of the FS-i6X Transmitter, showing the sticks, switches, and LCD screen.

Figure 4.3: Close-up view of the FS-i6X Transmitter's switches, knobs, and stick gimbals.

The transmitter is equipped with a PS/2 port for DSC (Direct Servo Control) and can be connected to a PC via an upgrade cable for simulator practice.

Figure 4.4: Rear view of the FS-i6X Transmitter, highlighting the Trainer Jack/Update Interface and power input.

The FS-i6X is versatile and compatible with various RC models, including multirotors, helicopters, fixed-wing aircraft, RC cars, RC boats, and even robots.

Figure 4.5: Illustration of different RC model types compatible with the FS-i6X transmitter.

The LCD screen provides essential information and allows for digital configuration. It supports displaying information in English or Chinese characters.

Figure 4.6: Close-up of the FS-i6X's backlit LCD screen, showing operational data.

4.2 FS-iA10B Receiver

The FS-iA10B is a 10-channel 2.4GHz receiver designed to work seamlessly with the FS-i6X transmitter. It features dual antennas for robust signal reception and supports i-BUS and data acquisition.

Figure 4.7: Top view of the FS-iA10B Receiver, showing channel ports and antenna connections.

Figure 4.8: Detailed view of the FS-iA10B Receiver's servo and i-BUS ports.

5. Setup

5.1 Battery Installation

The FS-i6X transmitter requires 4 x 1.5V AA batteries (not included). Open the battery compartment on the back of the transmitter and insert the batteries, ensuring correct polarity. Close the compartment securely.

5.2 Binding (Transmitter to Receiver)

The FS-i6X transmitter and FS-iA10B receiver are typically pre-bound from the factory. You should not need to bind them again upon receipt. However, if re-binding is necessary, follow these steps:

1. Ensure the transmitter is powered off.
2. Connect the bind plug to the B/VCC port on the FS-iA10B receiver.
3. Apply power to the receiver (e.g., via an ESC or external battery). The receiver's LED should flash rapidly.
4. While holding down the 'BIND KEY' button on the FS-i6X transmitter, power on the transmitter.
5. The transmitter's screen should indicate binding progress. Once bound, the receiver's LED will become solid.
6. Release the 'BIND KEY' button and power off both the transmitter and receiver.
7. Remove the bind plug from the receiver.
8. Power on the transmitter first, then the receiver. The receiver's LED should be solid, indicating a successful bind.

5.3 Connecting the Receiver

Connect your servos, ESCs, and other components to the appropriate channels on the FS-iA10B receiver. Refer to the markings on the receiver for channel assignments (CH1-CH10, i-BUS, SENS, B/VCC).

5.4 How to Setup 10 Channels

The FS-i6X transmitter defaults to 6 channels. To enable all 10 channels, follow these steps:

1. Long press the OK button for 2 seconds to enter the main menu setting.
2. Navigate to and select System setup to enter.
3. Scroll down to the last item, Aux SWitches (auxiliary switch setting), and enter.
4. Set switches SwA, B, C, D to On to activate them.
5. Change the channel assignment from Ch6 to Ch10.
6. Long press the CANCH key to automatically save the settings and exit the menu.

6. Operating

6.1 Basic Operation

To power on the transmitter, press and hold the power button until the LCD screen illuminates. To power off, press and hold the power button again until the screen turns off. Always ensure your model's power is off before powering off the transmitter.

6.2 Mode-2 Configuration

This FS-i6X transmitter is configured for Mode-2, which means the left stick controls throttle and rudder, while the right stick controls aileron and elevator. This is a common configuration for RC aircraft.

6.3 Simulator Connection

The FS-i6X supports connection to PC-based flight simulators. Use the provided upgrade cable to connect the transmitter's PS/2 port to your computer's USB port. This allows you to practice flying skills without risking your physical model. Note that simulator software must be purchased separately.

7. Maintenance

• Keep the transmitter and receiver clean and free from dust and debris. Use a soft, dry cloth for cleaning.
• Store the equipment in a cool, dry place, away from direct sunlight and extreme temperatures.
• Remove batteries from the transmitter if it will not be used for an extended period to prevent leakage.
• Regularly check all cables and connectors for wear or damage.

8. Troubleshooting

• No Power: Check battery installation and ensure batteries have sufficient charge.
• No Control/Intermittent Control: Verify that the transmitter and receiver are properly bound. Check all connections between the receiver and your model's components. Ensure there is no significant interference in your operating area.
• Receiver LED Flashing: This usually indicates the receiver is not bound to the transmitter or has lost signal. Re-bind the receiver to the transmitter if necessary.
• Display Issues: If the LCD display is dim or unreadable, check battery voltage.

9. Specifications

10. Warranty and Support

For warranty information, technical support, or service inquiries, please refer to the official FLYSKY website or contact their customer service directly. Keep your purchase receipt as proof of purchase for any warranty claims.