Battery Tender 800 AMP Peak Jump Starter User Manual

1. Introduction

The Battery Tender 800 AMP Peak Jump Starter is a compact and powerful portable device designed to jump start vehicles with up to V8 engines, including cars, pickup trucks, SUVs, and ATVs. It also functions as a 7200mAh power pack with a USB output for charging various electronic devices. This manual provides essential information for the safe and effective use, maintenance, and troubleshooting of your jump starter.

Figure 1.1: Battery Tender 800 AMP Peak Jump Starter with included jump cables.

2. Important Safety Information

Please read and understand all safety information before using this product. Failure to follow these instructions may result in electric shock, fire, or serious injury.

• Eye Protection: Always wear safety glasses when working with batteries.
• Ventilation: Ensure adequate ventilation when jump starting a vehicle.
• Avoid Short Circuits: Do not allow the positive and negative clamps to touch each other or the same piece of metal.
• Battery Type: This jump starter is designed for 12V lead-acid batteries. Do not use it on other battery types.
• Children and Pets: Keep the jump starter and its accessories out of reach of children and pets.
• Water Exposure: Do not expose the unit to rain or wet conditions.
• Disassembly: Do not attempt to disassemble, modify, or repair the unit. Refer all servicing to qualified personnel.
• Charging: Use only the charging cables provided or approved by Battery Tender.
• Temperature: Do not operate the unit in extreme temperatures. Refer to specifications for operating temperature range.

3. Package Contents

Verify that all items are present in your package:

• Battery Tender 800 AMP Peak Jump Starter (Model: 030-1010-WH)
• Heavy-duty Jump Cables with Clamps (Red and Black)
• USB Charging Cable (for charging the unit)
• User Manual (this document)

Figure 3.1: The jump starter unit connected to its heavy-duty jump cables.

4. Setup and Initial Charge

Before first use, it is crucial to fully charge your Battery Tender Jump Starter. This ensures optimal performance and extends battery life.

1. Check Battery Level: Press the power button on the unit to check the current charge level indicated by the LED lights. Four lights typically indicate a full charge.
2. Connect Charging Cable: Locate the USB input port on the side of the jump starter. Connect the provided USB charging cable to this port.
3. Connect to Power Source: Plug the other end of the USB charging cable into a USB wall adapter (not included) or a powered USB port.
4. Charge Fully: Allow the unit to charge until all LED indicator lights are solid, indicating a full charge. This may take several hours.

Figure 4.1: Side view of the jump starter showing the USB input and output ports.

5. Operating Instructions

5.1. Jump Starting a Vehicle

Follow these steps carefully to safely jump start your vehicle:

1. Prepare Vehicle: Ensure the vehicle's ignition is off and all accessories (lights, radio, AC) are turned off. Engage the parking brake.
2. Connect Red Clamp: Connect the RED positive (+) clamp to the positive (+) terminal of the vehicle's battery.
3. Connect Black Clamp: Connect the BLACK negative (-) clamp to a solid, unpainted metal part of the vehicle's engine block or chassis, away from the battery and fuel lines. Do not connect directly to the negative battery terminal unless specified by the vehicle manufacturer.
4. Connect Cables to Unit: Insert the cable connector into the jump start port on the Battery Tender unit. Ensure a secure connection. The indicator light on the cable connector should turn green if the connection is correct.
5. Start Vehicle: Once connected, start the vehicle's ignition. If the vehicle does not start immediately, wait 30 seconds before attempting again. Do not crank for more than 5 seconds at a time.
6. Disconnect Cables: Once the vehicle starts, immediately disconnect the jump cables from the Battery Tender unit. Then, disconnect the BLACK negative (-) clamp from the vehicle, followed by the RED positive (+) clamp from the battery.
7. Recharge Unit: For optimal readiness, recharge the jump starter as soon as possible after each use.

Figure 5.1: The heavy-duty red (positive) and black (negative) jump cables.

5.2. Charging USB Devices

The Battery Tender Jump Starter can also be used as a portable power bank to charge your electronic devices.

1. Connect Device: Plug your device's USB charging cable into the USB output port on the jump starter.
2. Begin Charging: The jump starter will automatically begin charging your device. The LED indicators will show the remaining power level of the jump starter.
3. Disconnect: Disconnect your device once it is fully charged or when you are finished charging.

Figure 5.2: The jump starter connected via USB to charge a tablet.

6. Maintenance

Proper maintenance ensures the longevity and reliability of your jump starter.

• Regular Recharging: To maintain the internal battery's health, fully recharge the jump starter every 3-6 months, even if it has not been used.
• Storage: Store the unit in a cool, dry place, away from direct sunlight, moisture, and extreme temperatures.
• Cleaning: Clean the unit with a soft, dry cloth. Do not use harsh chemicals or abrasive cleaners.
• Cable Inspection: Periodically inspect the jump cables and clamps for any signs of damage, fraying, or corrosion. Replace if necessary.

Figure 6.1: The compact size of the jump starter, making it easy to store and transport.

7. Troubleshooting

If you encounter issues with your jump starter, refer to the table below:

8. Product Specifications

9. Warranty & Support

For warranty information, technical support, or service inquiries, please contact Battery Tender customer service. Details regarding specific warranty terms and conditions can typically be found on the official Battery Tender website or by contacting their support directly.

Manufacturer: Battery Tender

Website: www.batterytender.com

UPC: 734357310108