Battery Tender 800 Amp Vehicle Jump Starter & Portable Inflator

Important Safety Instructions & Warnings

General Precautions

WARNING

• Save these instructions.
• Read all instructions before using the product.
• Close supervision is necessary when the product is used near children to reduce the risk of injury.
• Do not put fingers or objects into the product.
• Use of attachments not recommended or sold by the manufacturer may result in fire, electric shock, or injury.
• To reduce damage to the electric plug, pull on the plug, not the cord, when disconnecting.
• Do not use a damaged or modified battery pack or appliance. Damaged batteries may exhibit unpredictable behavior leading to fire, explosion, or injury.
• Do not operate the jump starter with a damaged cord or plug.
• Do not disassemble the jump starter; only qualified service technicians should service it. Incorrect reassembly may result in fire or electric shock.
• To reduce electric shock risk, unplug the jump starter from the outlet before servicing.

Risk of Explosive Gases

WARNING

Working in the vicinity of a lead-acid battery is dangerous. Batteries generate explosive gases during normal operation. It is of utmost importance to follow these instructions each time you use the power pack.

• To reduce the risk of battery explosion, follow these instructions and those published by the battery and equipment manufacturers. Review all cautionary markings on these products and on the engine.

Personnel Precautions

• Have someone nearby to assist when working near a lead-acid battery.
• Keep fresh water and soap nearby in case battery acid contacts skin, clothing, or eyes.
• Wear complete eye and clothing protection. Avoid touching eyes while working near the battery.
• If battery acid contacts skin or clothing, wash immediately with soap and water. If acid enters the eye, flood with cold water for at least 10 minutes and seek medical attention.
• NEVER smoke or allow sparks or flames near the battery or engine.
• Be cautious about dropping metal tools onto the battery, which could spark or short-circuit, causing an explosion.
• Remove personal metal items (rings, bracelets, watches) when working with a lead-acid battery, as it can produce a high short-circuit current capable of welding metal and causing severe burns.

General Warnings (Charging/Abuse)

WARNING

• When charging the jump starter's internal battery, work in a well-ventilated area and do not restrict ventilation.
• Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact occurs, flush with water. If liquid contacts eyes, seek medical help. Ejected liquid can cause irritation or burns.
• Do not expose the jump starter to fire or excessive temperature (above 130°C), as this may cause explosion.
• Have servicing performed by a qualified technician using only factory replacement parts.

Cautions

• Do not immerse in water.
• Do not use or store near sources of fire or a heater.
• Do not put into fire or apply direct heat.
• Do not pierce the casing.
• Do not strike, throw, or subject to severe physical shock.
• Do not attempt to modify in any way.
• Do not place in a microwave oven or pressurized container.
• Do not use if it gives off an odor or generates heat.
• Do not insert metal objects into the cable input opening, as this could cause a spark and electric shock.

Product Specifications

Product Overview

Items included in your retail box:

1. Vehicle Jump Starter & Portable Inflator
2. Smart Alligator Clips
3. USB Charging Cable
4. Inflator Hose
5. Inflator Nozzles (3)
6. Canvas Bag
7. Instruction Manual

Operating Instructions

Vehicle Jump Starter & Portable Inflator Features

The device features a central LCD screen displaying battery percentage and inflation pressure. It includes:

• USB-C Port (IN): 5V, 2A for charging the internal battery.
• USB Port (OUT): 5V, 2.1A for charging external devices.
• LED Light: Can be turned ON/OFF by holding the ON/OFF button for at least two (2) seconds.
• Portable Inflator Connection: For attaching the air hose.
• Smart Alligator Clip Receptacle Cover: For connecting the jump starter cables.
• Buttons:
• INFLATOR MODE: Cycles through display modes (PSI, BAR, KPA, Battery Level %).
• INCREASE PRESSURE (+): Adjusts pressure settings.
• DECREASE PRESSURE (-): Adjusts pressure settings.
• INFLATOR START/STOP: Starts or stops the inflation process.
• POWER TO JUMP START: Activates the jump start function (800 Cranking Amps).
• 140 PSI CAPACITY: Maximum pressure for the inflator.

The device is a compact, black unit with a digital display showing "100". It has various ports and buttons labeled for its functions: USB-C IN, USB OUT, LED Light ON/OFF, Portable Inflator Connection, and a receptacle for smart alligator clips. Control buttons include Inflator Mode, Increase Pressure (+), Decrease Pressure (-), and Inflator Start/Stop. It also indicates 140 PSI Capacity and Power to Jump Start (800 Cranking Amps).

Jump Starting a Vehicle

1. Before jump starting, consult your vehicle manufacturer's instructions/recommendations.
2. Check the internal battery charge status by pressing the "Power Button" for 2 seconds. The power will turn on, and the battery percentage will display on the LCD screen.
3. Ensure there is at least 50% battery level available.
4. Insert the smart alligator clip connector into the Jump Pack.
5. Connect the RED positive clip to the positive battery post.
6. Connect the BLACK negative clip to the negative battery post.
7. CAUTION: Ensure the Jump Pack and cables are clear of all vehicle fan blades, belts, pulleys, etc. before proceeding.
8. The LED on the smart alligator clips will turn solid GREEN. Wait 5 to 10 seconds, then start your vehicle.
9. Remove the clips IMMEDIATELY after the vehicle has started. Remove the Black negative clamp first.
10. DO NOT use the Jump Starter to repeatedly try to start your vehicle. Wait at least thirty (30) seconds between attempts. Check the vehicle after three attempts.

Smart Alligator Clips Indicators

The smart alligator clips have a Green and Amber LED and a warning buzzer for faults and errors:

• Correct Connection: LED changes from flashing Green to solid Green.
• Standby Mode (No Connection/Bad Connection): Green LED flashes.
• Low Battery (<14V): Amber LED lights up solid, buzzer beeps slowly.
• High Battery (>17.5V): Amber LED lights up solid, buzzer sounds solid. (Indicates clips plugged into an incorrect voltage jump pack).
• Reverse Polarity: (Red clip to Black negative terminal, Black clip to Red positive terminal). Amber LED lights up solid, buzzer beeps rapidly.
• Short Circuit Protection: Amber LED lights up solid, buzzer beeps rapidly.
• Overheat Protection: Amber LED flashes, buzzer beeps slowly.

Portable Inflator Operation

1. Connect the supplied air hose to the unit's connection.
2. Press and hold the "Power Button" for 2 seconds to turn the unit on. The battery percentage will be displayed on the LCD screen.
3. Press the "Inflator Mode" button to change the display to the Inflator Mode Screen.
4. The Inflator Mode Screen displays pressure units (PSI, BAR, KPA) and Battery Level %.
5. The default setting is 36.0 PSI. To change units (PSI/BAR/KPA), press the "Inflator mode" button with a single press.
6. To adjust the automatic cut-off pressure setting, press either the "+" or "-" button to adjust the value up or down.
7. Connect the inflator hose to the valve stem of the item to be inflated.
8. Press the "Inflator Start/Stop" button to start or stop the inflation.
9. The inflator will shut off automatically at the preset pressure.

Inflator Cautions

• For items with inflation pressure less than the air pump's range (e.g., balloons, balls, swimming rings), inflation may not stop automatically at the preset pressure. Be careful when using it under these conditions.
• Always check the required air pressure and the maximum air pressure when inflating tires.

Charging the Vehicle Jump Starter & Portable Inflator

1. Use the supplied USB cable to charge the unit. NOTE: While charging, none of the other features and functions are active.
2. Once the internal battery level reaches 100%, the charge is complete, and the unit will turn off after 10 seconds.
3. The battery level should be checked and charged every three (3) months.
4. When charging the internal battery, work in a well-ventilated area and do not restrict ventilation in any way.

Charging & Storage Cautions

• The device shall be stored indoors and protected from the elements.
• The unit shall not be charged outdoors.
• When in use, take steps to reduce exposure to rain, sleet, snow, and the like.

User Maintenance Instructions

• The battery level should be checked, and the unit charged every three (3) months. Keeping the internal battery fully charged ensures the unit is ready when needed and extends the battery's life.
• Store the unit in a clean, dry environment at room temperature if possible.
• If you notice a bulge in the case or a chemical smell, STOP using the unit immediately and seek technical help.

Trouble Shooting

Regulatory Information

FCC Warning

Title 47 Subpart, 15.105(b)

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in residential installations. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception. The user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

ICES-001: Industrial, Scientific, and Medical (ISM) Radio Frequency Generators

This product has been tested and found to be compliant with the listed standards and found to be compliant with the Code of Industry Canada ES-001 and the measurement Procedure according to CISPR 11.

CAN ICES-001B / NMB-001B

Customer Service

For customer support, please visit batterytender.com. You can also call our customer service hotline: 877-456-7901.

Warranty

The Battery Tender® Vehicle Jump Starter & Portable Inflator comes with a twelve (12) month limited warranty against defects or failure (within one (1) year of purchase).

THIS LIMITED WARRANTY IS VOID under the following conditions:

1. The product is misused, subjected to careless handling, or operated under conditions of extreme temperature, shock, or vibration beyond recommendations for safe and effective use.
2. The product is disassembled or repaired by anyone who is not an authorized service representative of Battery Tender®.
3. The product was purchased from an unauthorized source. Warranty is not transferable from the original purchaser.
4. Any physical damage to any of the components or any accessory after purchase.
5. Any modifications to any of the components.
6. Any corrosion, including salt water damage.