1. Introduction
This manual provides essential information for the safe and effective use of your BORNMIO CS-MLE200SL replacement Ni-MH battery. This battery is designed for compatibility with MINELAB Quattro detectors, including models that use part numbers 3011-0170, 3011-0196, ML-FBS, and XQ1699356. Please read these instructions carefully before installation and use.
2. Safety Information
- Do not disassemble, crush, or puncture the battery.
- Do not expose the battery to high temperatures (above 60°C / 140°F) or direct sunlight.
- Do not short-circuit the battery terminals.
- Keep the battery away from water and moisture.
- Use only chargers specified for Ni-MH batteries.
- Dispose of used batteries according to local regulations.
- Keep out of reach of children.
3. Setup and Installation
3.1 Initial Charging
Before first use, fully charge the battery. Connect the battery to a compatible Ni-MH battery charger. The charging time may vary depending on the charger and the battery's initial charge level. Refer to your charger's instructions for specific charging procedures.
3.2 Battery Installation
- Ensure your MINELAB Quattro detector is powered off.
- Locate the battery compartment on your detector. Refer to your detector's user manual for specific instructions on opening the compartment.
- Carefully insert the BORNMIO CS-MLE200SL battery into the compartment, ensuring the terminals align correctly. Do not force the battery.
- Close the battery compartment securely.
Image 1: Top view of the BORNMIO CS-MLE200SL Ni-MH battery, illustrating its two-cell cylindrical design and product label.
4. Operating Instructions
Once installed and charged, the battery powers your MINELAB Quattro detector. The battery features built-in protection against overcharge, over-discharge, over-voltage, and short circuits to ensure safe and reliable operation.
- Powering On: Follow your detector's instructions to power it on.
- Monitoring Battery Level: Regularly check the battery indicator on your detector to avoid unexpected power loss during use.
- Recharging: Recharge the battery when the detector indicates a low power level. Avoid completely draining the battery to prolong its lifespan.
Image 2: Side view of the BORNMIO CS-MLE200SL Ni-MH battery, highlighting its full length and the detailed information on the product label.
5. Maintenance and Storage
5.1 General Maintenance
- Keep the battery terminals clean and free from dirt or corrosion.
- Avoid exposing the battery to extreme temperatures or humidity.
- Do not drop or subject the battery to strong impacts.
5.2 Storage
If storing the battery for an extended period, ensure it is partially charged (around 50-70% of its capacity). Store it in a cool, dry place, away from direct sunlight and extreme temperatures. Recharge the battery every 3-6 months during long-term storage to prevent deep discharge.
6. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Battery not charging | Charger malfunction; improper connection; battery too hot/cold. | Check charger and cable connections. Ensure battery is at room temperature. Try a different compatible charger. |
| Short operating time | Battery not fully charged; aging battery; high power consumption by device. | Ensure full charge before use. If battery is old, consider replacement. Reduce device power settings if possible. |
| Detector not powering on | Battery not installed correctly; battery discharged; faulty detector. | Re-install battery, ensuring proper contact. Charge battery fully. Test with another known good battery if available. |
7. Specifications
- Model: CS-MLE200SL
- Battery Type: Ni-MH (Nickel-Metal Hydride)
- Voltage: 9.6V
- Capacity: 2000mAh (19.20Wh)
- Dimensions: 200.20 x 29.26 x 14.50 mm (7.88 x 1.15 x 0.57 inches)
- Weight: 250g (8.82 oz)
- Certifications: ISO9001, RoHS, CE
- Protection Features: Overcharge, Over-discharge, Over-voltage, Short-circuit protection
- Compatible Models: MINELAB Quattro detectors, MINELAB Quattro MP
- Compatible Part Numbers: 3011-0170, 3011-0196, ML-FBS, XQ1699356
8. Warranty and Support
8.1 Warranty Information
This BORNMIO battery comes with a 12-month warranty from the date of purchase. Additionally, a 14-day money-back guarantee is offered. This warranty covers manufacturing defects. It does not cover damage caused by misuse, accident, unauthorized modification, or normal wear and tear.
8.2 Customer Support
For technical assistance, warranty claims, or any questions regarding your BORNMIO battery, please contact your retailer or the manufacturer directly. Please have your purchase details and model number (CS-MLE200SL) available when contacting support.