Introduction
The LUXPRO LP172 Waterproof Micro LED Puck Lights are versatile, battery-operated lighting solutions designed for various indoor and outdoor applications. These compact lights feature an IPX6 waterproof rating, making them ideal for illuminating small and dark spaces such as under cabinets, inside tackle boxes, or on bookshelves. Each light provides bright illumination and is equipped with an adhesive backing for easy installation.
Image: A set of five LUXPRO LP172 Waterproof Micro LED Puck Lights, showcasing their compact design and the included CR2032 battery.
Setup and Installation
Your LUXPRO LP172 puck lights come with batteries pre-installed and an adhesive backing for immediate use. Follow these steps for proper installation:
- Unpack: Carefully remove the puck lights from their packaging.
- Select Location: Choose a clean, dry, and smooth surface for mounting. Ensure the area is free of dust, grease, or moisture.
- Prepare Surface: Clean the chosen surface with a suitable cleaner and allow it to dry completely.
- Apply Adhesive: Peel off the protective film from the 3M adhesive pad located on the back of the puck light.
- Mount Light: Press the puck light firmly onto the prepared surface for at least 30 seconds to ensure a strong bond.
Image: A LUXPRO puck light being installed using its adhesive backing on a surface, demonstrating its ease of attachment.
Operating Instructions
The LUXPRO LP172 puck lights are designed for simple operation:
- Turning On: Press the center of the light (the power button icon) once to turn the light on.
- Turning Off: Press the center of the light again to turn the light off.
Each light provides up to 10 hours of continuous illumination on a fresh set of batteries.
Image: A LUXPRO puck light emitting bright light in a dark environment, highlighting its 16 lumen output.
Image: A LUXPRO puck light providing illumination inside a drawer, demonstrating its utility and 10-hour run time.
Maintenance
Battery Replacement
Each LUXPRO LP172 light requires two CR2032 batteries. When the light dims or stops functioning, it's time to replace the batteries. Due to safety regulations, a plastic safety retainer is present in the battery compartment. Follow these steps:
- Unscrew Base: Gently turn the base of the puck light counter-clockwise to unscrew and remove it.
- Remove Safety Retainer: Locate the plastic safety retainer inside the battery compartment. This retainer has two small holes. Use a small tool, such as a jeweler's screwdriver or a paperclip, to engage these holes and twist the retainer counter-clockwise until it can be removed.
- Access Batteries: Press down gently on the power button (the center of the light) to pop out the battery compartment.
- Replace Batteries: Remove the old CR2032 batteries and insert two new CR2032 batteries, ensuring correct polarity (+/-).
- Reassemble: Place the battery compartment back into the light. Reinsert the plastic safety retainer and twist it clockwise with your small tool until it is securely in place. Finally, screw the base back onto the light by turning it clockwise until snug.
Image: A step-by-step diagram illustrating the process of replacing batteries in the LUXPRO puck light, including unscrewing the base, removing the plastic safety retainer, accessing the battery sleeve, replacing batteries, and reassembling the unit.
Cleaning
To clean your puck lights, wipe the exterior with a soft, damp cloth. Do not use abrasive cleaners or submerge the entire unit in water, despite its waterproof rating, to prevent damage to internal components.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Light does not turn on. | Dead batteries or incorrect battery installation. | Replace batteries following the instructions in the Maintenance section. Ensure correct polarity. |
| Light is dim. | Low battery power. | Replace batteries. |
| Difficulty removing plastic safety retainer during battery replacement. | The retainer is designed to be secure for safety. | Use a small, pointed tool (e.g., jeweler's screwdriver, paperclip) to engage the two small holes on the retainer and twist it counter-clockwise. Apply firm but gentle pressure. |
| Adhesive not holding. | Surface not clean or smooth, or insufficient pressure during application. | Ensure surface is clean, dry, and smooth. Apply firm pressure for at least 30 seconds. For rougher surfaces, consider additional adhesive solutions. |
Specifications
| Feature | Detail |
|---|---|
| Model Name | LP172 |
| Brand | LUXPRO |
| Light Source Type | LED |
| Power Source | 2 x CR2032 batteries (included) |
| Voltage | 6 Volts |
| Run Time | Up to 10 hours |
| Water Resistance Level | IPX6 Waterproof |
| Mounting Type | Adhesive |
| Switch Type | Push Button / Touch |
| Product Dimensions | 1.22"D x 1.22"W x 0.64"H |
| Item Weight | 0.64 ounces (per light) |
| Material | Plastic, Silicone |
| Indoor/Outdoor Usage | Indoor, Outdoor |
| UPC | 812436011723 |
Image: A LUXPRO puck light demonstrating its IPX6 water-resistant rating, indicating protection against high-pressure water jets.
Warranty Information
LUXPRO products are designed for quality and durability. For specific warranty details regarding your LP172 Waterproof Micro LED Puck Lights, please refer to the packaging or visit the official LUXPRO website. General warranty terms typically cover manufacturing defects under normal use.
Customer Support
For further assistance, technical support, or inquiries about your LUXPRO LP172 Waterproof Micro LED Puck Lights, please contact LUXPRO customer service or visit their official website:
- LUXPRO Official Store: Visit the LUXPRO Store on Amazon
- Manufacturer Website: Refer to product packaging for the direct manufacturer website or search online for "LUXPRO official website".