1. Introduction
This manual provides essential instructions for the safe and proper use of your NERF Alpha Strike Stinger SD-1 Targeting Set. Please read all instructions carefully before assembly and operation. Retain this manual for future reference.
2. Important Safety Information
WARNING: To avoid injury, do not aim at eyes or face. Use only official NERF darts. Other darts may not meet safety standards. Do not modify darts or dart blaster.
- Always wear eye protection when using this product (not included).
- Do not aim or shoot at people or animals.
- Do not modify the blaster or darts.
- Keep small parts away from children under 3 years of age to prevent choking hazards.
- Adult supervision is recommended for young users.
3. Included Components
Your NERF Alpha Strike Stinger SD-1 Targeting Set includes the following items:
- 1x Stinger SD-1 Blaster
- 2x Half-Targets (can be combined to form 1 full target)
- 4x Official NERF Elite Darts
Image 3.1: All components included in the set: the Stinger SD-1 blaster, two half-targets, and four NERF Elite darts.
4. Setup Instructions
4.1. Preparing the Stinger SD-1 Blaster
The Stinger SD-1 blaster comes pre-assembled and does not require any additional assembly. No batteries are required for operation.
4.2. Assembling the Targets
The set includes two half-targets. These can be used individually or combined to create a single, larger target. To combine, align the interlocking tabs on the flat edges of the two half-targets and press them together until they securely snap into place.
5. Operating the Blaster
Follow these steps to load and fire your Stinger SD-1 blaster:
- Load a Dart: Insert one Official NERF Elite dart into the front barrel of the blaster until it is fully seated.
- Prime the Blaster: Pull the priming handle located at the bottom of the blaster all the way back until you hear a click. This action prepares the blaster to fire.
- Fire the Blaster: Aim at your target and press the trigger to launch the dart.
Image 5.1: Loading an Official NERF Elite dart into the blaster's barrel.
Image 5.2: Firing the Stinger SD-1 blaster towards a target.
6. Maintenance
The NERF Alpha Strike Stinger SD-1 requires minimal maintenance.
- Cleaning: Wipe the blaster and targets with a damp cloth to remove dust or dirt. Do not submerge in water.
- Storage: Store the blaster, darts, and targets in a cool, dry place away from direct sunlight when not in use.
- Darts: Inspect darts regularly for damage. Discard any darts that are torn or significantly damaged, as they may affect performance or safety.
7. Troubleshooting
If you encounter issues with your Stinger SD-1 blaster, refer to the following common problems and solutions:
- Dart not firing or weak shot:
- Ensure the dart is fully inserted into the barrel.
- Confirm the blaster is fully primed by pulling the handle all the way back until it clicks.
- Check if the dart is damaged. Use only official, undamaged NERF Elite darts.
- Priming handle stuck:
- Ensure no dart is jammed in the barrel.
- Do not force the priming handle. If it remains stuck, contact customer support.
8. Specifications
| Product Name | NERF Alpha Strike Stinger SD-1 Targeting Set |
| Model Number | SD-1 (Item model number: 220448) |
| Brand | Nerf |
| Product Dimensions | 9.76 x 1.73 x 9.02 inches |
| Item Weight | 3.52 ounces |
| Recommended Age | 0 - 8 years (Manufacturer recommended) |
| Power Source | Manual (No batteries required) |
9. Warranty Information
Specific warranty details for the NERF Alpha Strike Stinger SD-1 Targeting Set are typically provided with the product packaging or can be found on the official Nerf website. Please refer to those resources for the most current warranty terms and conditions.
10. Customer Support
For further assistance, questions, or to report issues, please visit the official Nerf website or contact their customer service department. Contact information is usually available on the product packaging or the brand's official online presence.
