ECOCONUT Tailgate Handle Rear View Camera User Manual

1. Product Overview

The ECOCONUT Tailgate Handle Rear View Camera is a replacement tailgate handle with an integrated backup camera, designed to enhance safety and convenience when reversing your vehicle. This system provides a clear view of the area behind your vehicle, assisting with parking and maneuvering.

Compatibility: This camera system is specifically designed for Toyota Tundra models from 2007, 2008, 2009, 2010, 2011, 2012, and 2013.

2. Package Contents

Please verify that all items are present in the package before beginning installation:

• 1x Backup Camera with Tailgate Handle
• 1x Extension Cable (approximately 21.5 ft)
• 1x User Manual (this document)
• 1x RCA Barrel Connector

3. Key Features

• Waterproof Design: Ensures reliable performance in various weather conditions.
• Wide View Angle Camera: Provides a broad perspective of the rear area.
• Night Vision: Improved performance in low-light conditions.
• Parking Lines: Features switchable parking guidelines for precise maneuvering.
• Integrated Tailgate Handle: Replaces the original handle without altering the vehicle's aesthetics or original trunk switch function.

4. Installation Guide

This section provides general installation instructions. Professional installation is recommended if you are unfamiliar with automotive electrical systems.

4.1. Preparation

• Ensure the vehicle's ignition is off and the battery is disconnected to prevent electrical shorts.
• Gather necessary tools: screwdriver set, wire strippers, electrical tape, multimeter, zip ties.
• Remove the existing tailgate handle.

4.2. Camera and Handle Installation

1. Install the new tailgate handle with the integrated camera into the tailgate opening. Ensure it fits securely.
   

   Image: The ECOCONUT tailgate handle with the integrated rear view camera. The camera lens is visible on the left side of the handle assembly.

2. Route the camera cable from the tailgate into the vehicle's cabin. It is recommended to route the cable along the driver's side of the vehicle to ensure sufficient length.
   

   Image: The coiled 21.5 ft extension cable, featuring a yellow RCA connector and red/black power wires at one end, and a female camera connector at the other.

3. Connect the camera cable to the extension cable. Ensure the arrows on the connectors are aligned for a proper match.

4.3. Power Connection

The camera requires a 12V power supply.

1. Identify Power Source:
   • For Camera On Only When Reversing: Connect the red power cable (from the extension cable) to the positive (+) wire of your vehicle's reverse light. Use a multimeter to identify the correct positive wire (e.g., blue/red wire in some Tundra models). Connect the black ground cable to a suitable chassis ground or the negative (-) wire of the reverse light.
   • For Camera Always On (if desired): Connect the red power cable to a switched 12V power source (e.g., accessory power) and the black ground cable to a chassis ground.
2. Secure all connections with electrical tape or heat shrink tubing.

4.4. Video Signal Connection to Aftermarket Display

1. Connect the yellow RCA connector from the extension cable to the video input (typically labeled "RCIN" or "Camera Input") on your aftermarket display or head unit.
2. If your aftermarket display has a reverse trigger wire (e.g., purple or pink wire), connect the red power wire from the camera's extension cable (the one connected to the reverse light) to this trigger wire. This tells the head unit to switch to the camera view when reverse is engaged.
3. Parking Line Adjustment: The camera comes with built-in parking guidelines. If your aftermarket display also provides adjustable parking lines and you prefer to use those, you can disable the camera's built-in lines. Locate the two small green wires labeled "Parking line" on the camera harness near the power connection. Solder or twist these two green wires together to disable the camera's default parking lines.
   

   Image: A close-up view of the camera harness showing two small green wires labeled "Parking line". These wires can be connected to disable the camera's internal parking guidelines.

Note: A monitor or navigation unit is NOT included. You may need an additional adapter or interface (not included) if connecting to a factory radio.

5. Operating Instructions

Once properly installed and connected to your aftermarket display, the ECOCONUT Rear View Camera operates automatically.

1. Turn on your vehicle's ignition and ensure your aftermarket display is powered on.
2. Shift your vehicle into reverse gear.
3. The display should automatically switch to the camera's view, showing the area behind your vehicle with parking guidelines (if enabled).
4. Use the camera view to assist with safe backing and parking maneuvers.

Image: A close-up view of the camera lens integrated into the tailgate handle, showing its position for optimal rear visibility.

6. Maintenance

• Regularly clean the camera lens with a soft, damp cloth to ensure a clear view. Avoid abrasive cleaners.
• Periodically check all wiring connections for corrosion or damage.
• Ensure the tailgate handle mechanism remains free of debris and operates smoothly.

7. Troubleshooting

8. Specifications

9. Warranty and Support

Specific warranty information for this product is not provided in this manual. For details regarding warranty coverage, returns, or technical support, please refer to the product's listing page on the retailer's website or contact ECOCONUT customer service directly.

You can often find contact information for ECOCONUT through their official brand store on Amazon or by searching for "ECOCONUT customer support" online.