Introduction
This manual provides detailed instructions for the assembly, operation, and maintenance of your PERLESMITH PSTM1 TV Tripod Stand. Designed for versatility and stability, this stand accommodates most 23-70 inch LED, LCD, and OLED flat screen TVs, supporting up to 88 lbs. It features height adjustability, 360° swivel, and compatibility with various VESA patterns.
Please read this manual thoroughly before installation and use to ensure safe and proper operation.
Setup and Assembly
The PERLESMITH PSTM1 TV Tripod Stand is designed for super easy installation and portability, allowing for quick setup and takedown. No drilling into walls is required.
Package Contents
Before you begin, ensure all parts listed in the included parts list are present. Refer to the separate Installation Manual (PDF) for a complete list of components and detailed step-by-step assembly instructions. You can access the PDF manual here.
Assembly Overview
Assembly typically takes around 10 minutes. Follow the instructions carefully to ensure proper and secure setup.
Figure 1: Stable & Modern Appearance. This image highlights key stability features including safety screws, level adjustment screws, tilt adjustment screws, and non-slip feet, ensuring a secure setup for your television.
Figure 2: Easy Installation. This diagram provides an overview of the stand's dimensions (17.24" width, 16.65" height for the TV plate, 25.59" base spread) and confirms its 88 lbs weight capacity, suitable for 23-60 inch TVs, with an estimated 10-minute assembly time.
Ensure all screws are tightened securely, especially the safety pin, to prevent accidental drops. The non-slip feet provide a stable base and protect your flooring.
Operating Instructions
The PERLESMITH PSTM1 TV Tripod Stand offers flexible viewing options to enhance your experience.
Height Adjustment
The flexible pole allows for easy height adjustment from 39.76 inches to 69.49 inches. Utilize the height adjustment knob and security pin to set your desired viewing height. There are five fixed different viewing positions to achieve perfect TV height.
Figure 3: 5 Height Adjustment. This image illustrates the adjustable height range of the stand, from a minimum of 42.52 inches to a maximum of 67.72 inches (measured from the top of the TV plate). It also shows the knobs for height adjustment, fixing the TV plate, and adjusting the feet.
Swivel and Tilt Functionality
The stand features a 360° swivel function, allowing you to easily adjust the viewing angle without moving the entire stand. Additionally, the TV mount can be tilted ±20° and leveled ±3° for optimal viewing comfort.
Figure 4: 360° Wider Viewing Range. This image demonstrates the stand's full 360-degree swivel capability and its tilt range of +5° to -15°, along with a level adjustment of ±3°, providing a wide range of viewing angles.
Maintenance
To ensure the longevity and safe operation of your PERLESMITH TV Tripod Stand, follow these simple maintenance guidelines:
- Regularly check all screws and connections to ensure they remain tight. Loose connections can compromise stability.
- Clean the stand with a soft, dry cloth. Avoid abrasive cleaners or solvents that could damage the finish.
- Do not exceed the maximum weight capacity of 88 lbs.
- When moving the stand, ensure the TV is securely mounted and the tripod legs are properly retracted or secured to prevent tipping.
Troubleshooting
If you encounter any issues with your PERLESMITH TV Tripod Stand, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Stand feels unstable or wobbly. | Loose screws or uneven leg extension. | Ensure all assembly screws are tightened. Adjust tripod legs to be fully extended and on a level surface. |
| TV does not swivel or tilt smoothly. | Adjustment knobs are too tight or mechanism is stiff. | Loosen the swivel/tilt adjustment knobs slightly. Apply a small amount of silicone lubricant if necessary (avoid oil-based lubricants). |
| Cannot adjust height. | Security pin is engaged or height adjustment knob is too tight. | Disengage the security pin. Loosen the height adjustment knob before attempting to raise or lower the pole. |
| TV not fitting the VESA mount. | Incorrect VESA pattern or TV size. | Verify your TV's VESA pattern (100x100mm to 400x400mm) and size (23-70 inches) against the stand's specifications. |
If the problem persists, please contact PERLESMITH customer support.
Specifications
| Feature | Detail |
|---|---|
| Model Number | PSTM1 |
| Compatible TV Sizes | 23-70 Inches |
| Maximum Weight Capacity | 88 lbs |
| VESA Compatibility | 100x100mm, 200x100mm, 200x200mm, 300x200mm, 200x300mm, 300x300mm, 400x300mm, 400x400mm |
| Height Adjustment Range | 39.76" to 69.49" |
| Swivel Angle | 360° |
| Tilt Angle | ±20° |
| Level Adjustment | ±3° |
| Material | Alloy Steel |
| Product Dimensions | 42 x 9 x 6 inches |
| Item Weight | 17 pounds |
| Manufacturer | PERLESMITH |
Warranty and Support
PERLESMITH offers a 10-year service guarantee for this product. For any questions, concerns, or assistance, please contact PERLESMITH customer support. You can also visit the official PERLESMITH store on Amazon for more information and products: PERLESMITH Store.
