UpStart Components 3949247 Washer Lid Switch Replacement Instruction Manual

1. Introduction

This manual provides detailed instructions for the installation, operation, maintenance, and troubleshooting of the UpStart Components 3949247 Washer Lid Switch. This component is designed as a direct replacement part for specific washing machine models, including the Whirlpool LSR6132HQ1. Please read this manual thoroughly before attempting any installation or repair to ensure safe and correct procedures.

2. Safety Information

Your safety and the proper functioning of your appliance are paramount. Adhere to the following safety guidelines:

• Disconnect Power: Always unplug the washing machine from its power source before beginning any repair or maintenance. Failure to do so can result in electric shock or serious injury.
• Wear Protective Gear: Use appropriate personal protective equipment, such as gloves, to prevent injury.
• Professional Assistance: If you are unsure about any step or uncomfortable performing the repair, consult a qualified appliance technician.
• Handle with Care: The lid switch contains electrical components. Handle it carefully to avoid damage.

3. Package Contents

Verify that all components are present and undamaged upon opening the package:

• 1 x UpStart Components 3949247 Washer Lid Switch

Figure 3.1: The UpStart Components 3949247 Washer Lid Switch. This image displays the complete lid switch assembly, including the main switch body, wiring harness, and electrical connector.

4. Compatibility

This UpStart Components 3949247 Washer Lid Switch is compatible with the Whirlpool LSR6132HQ1 Washing Machine and other models that use the following part numbers:

• 3949247V
• AP5983746
• 3949247
• 3949237
• 3949239
• 3949240
• 3949247VP
• PS11722098

5. Installation Instructions

The following steps outline the general procedure for replacing a washer lid switch. Specific washing machine models may vary slightly in disassembly. Refer to your appliance's service manual if available.

1. Disconnect Power: Unplug the washing machine from the electrical outlet. Turn off the water supply valves to the washer.
2. Access the Control Panel: Depending on your washer model, you may need to lift the control panel. Typically, there are two screws at the back of the control panel that need to be removed. Once removed, the control panel can usually be tilted up and back.
3. Open the Washer Cabinet: After lifting the control panel, locate the clips or screws that secure the washer's outer cabinet. Release these fasteners. The cabinet can then be tilted forward and lifted off the base.
4. Locate the Old Lid Switch: The lid switch is usually mounted near the top opening of the washer tub, often on the top frame or under the lid hinge. It will have a wiring harness connected to it.
5. Disconnect Wiring: Carefully disconnect the electrical connector from the old lid switch. Note the orientation of the wires if they are not color-coded or if there are multiple connectors.
6. Remove the Old Lid Switch: Unfasten the screws or clips holding the old lid switch in place. Remove the switch and its wiring harness from the washer.


Figure 5.1: A view of the lid switch with its integrated wiring harness and connector. This image highlights the electrical connections that need to be properly attached.

7. Install the New Lid Switch: Position the new UpStart Components 3949247 lid switch in the same location as the old one. Secure it with the screws or clips. Ensure it is firmly seated.


Figure 5.2: Close-up of the lid switch mechanism. This view shows the part of the switch that interacts with the washer lid to detect its open or closed state.

8. Reconnect Wiring: Connect the electrical connector from the washer's main harness to the new lid switch. Ensure a secure connection.

Figure 5.3: Another perspective of the lid switch, emphasizing the connector end of the wiring. Proper connection of this plug is essential for the switch to function.
9. Reassemble Washer: Carefully reattach the washer cabinet, ensuring all clips and screws are secured. Lower and secure the control panel.
10. Restore Power and Test: Plug the washing machine back into the electrical outlet and turn on the water supply. Run a short test cycle to ensure the lid switch functions correctly (e.g., the washer should pause or stop if the lid is opened during operation).

6. Operation

The washer lid switch is a critical safety component. Its primary function is to detect whether the washing machine lid is closed. When the lid is open, the switch prevents the washer from agitating or spinning, thereby protecting users from moving parts. When the lid is closed, the switch signals the control board that it is safe to proceed with the wash cycle.

7. Maintenance

The UpStart Components 3949247 Washer Lid Switch is a sealed unit and generally requires no specific maintenance. However, periodic inspection can help ensure its longevity:

• Visual Inspection: Occasionally inspect the switch and its wiring for any visible signs of wear, damage, or corrosion.
• Keep Area Clean: Ensure the area around the lid switch is free from lint, debris, or detergent residue that could interfere with its operation.

8. Troubleshooting

If your washing machine exhibits issues after replacing the lid switch, consider the following:

9. Specifications

• Part Number: AP-3949247-DL170 (UpStart Components)
• Compatible Part Numbers: 3949247V, AP5983746, 3949247, 3949237, 3949239, 3949240, 3949247VP, PS11722098
• Manufacturer: UpStart Components
• First Available: May 24, 2019

10. Warranty and Support

This UpStart Components replacement part is covered by a warranty provided solely by UpStart Components. It is not affiliated with any original equipment manufacturer (OEM) brands, and any warranties from original manufacturers do not apply to this product. For warranty claims, technical support, or further assistance, please contact UpStart Components directly through their official support channels.