Introduction
This manual provides comprehensive instructions for the installation, operation, and maintenance of your Wet Sounds REV 10 B-FC SA V2 Revolution Series 10-inch Tower Speakers. These speakers are designed to deliver full-range sound quality at long distances, suitable for marine environments. The REV TEC technology allows for consistent sound projection up to 80 feet and beyond.
The REV 10 speakers are constructed with durable materials, including a Kevlar reinforced cone and polyurethane surround, engineered to withstand challenging elements. They feature a Pro-Axial Driver with a coaxially mounted titanium diaphragm for high-frequency output.
Safety Information
Please read all safety instructions before installing and operating the speakers. Failure to follow these guidelines may result in injury or damage to the equipment.
- Electrical Connections: Ensure all wiring is performed by a qualified professional to prevent electrical hazards and ensure proper functionality. Incorrect wiring can damage the speakers or your vessel's electrical system.
- Mounting: Securely mount the speakers using the provided hardware. Improper mounting can lead to speakers detaching during operation, causing damage or injury.
- Water Exposure: While these speakers are waterproof, avoid submerging them. Ensure all connections are sealed to prevent water intrusion into the wiring.
- Volume Levels: Prolonged exposure to high volume levels can cause hearing damage. Operate the audio system at safe listening levels.
Package Contents
Verify that all items are present in the package:
- Wet Sounds REV 10 Tower Speakers (Pair)
- Fixed Aluminum Clamps (Pair)
- Mounting Hardware
- Instruction Manual
Specifications
| Feature | Specification |
|---|---|
| Model Name | REV-10-B-FC-SA-V2 |
| Speaker Type | Woofer |
| Impedance | 4 Ohms |
| RMS Watts | 300 Watts |
| Peak Watts | 600 Watts |
| Frequency Response | 20Hz to 20KHz |
| Sensitivity | 92 dB at 1 watt/1 meter |
| Mid Bass Driver | 10-inch Kevlar reinforced EFG cone woofer with polyurethane surround |
| High Frequency Driver | Pro-Axial Driver - Coaxially mounted Titanium Diaphragm High Output |
| Speaker Dimensions (Front-Back) | 13 inches (330.20mm) |
| Speaker Dimensions (Hang Height) | 11 9/16 inches (293.68mm) |
| Speaker Dimensions (Width) | 10 5/8 inches (269.87mm) |
| Speaker Weight (Each) | 14.8 pounds (6.71 kg) |
| Waterproof Rating | True |
| Maximum Sound Projection Range | 80 Feet |
| Mounting Type | Clamp Mount |
| Connectivity Technology | Coaxial, Wired (for subwoofer) |
| Audio Output Mode | Surround |
Setup and Installation
The REV 10 speakers are designed for clamp mounting. Proper installation is crucial for optimal performance and safety. It is recommended to have these speakers installed by a professional marine audio technician.
Mounting the Speakers
The speakers come with fixed aluminum clamps for secure attachment to your vessel's tower. Ensure the mounting surface is strong enough to support the weight of the speakers and withstand marine conditions.
- Identify the desired mounting location on your tower. Ensure there is sufficient clearance for the speakers and their rotation.
- Disassemble the clamp components as needed to fit around the tower bar.
- Position the clamp base on the tower and secure the speaker enclosure to the clamp using the provided hardware.
- Tighten all fasteners evenly to ensure a firm, vibration-free mount. Do not overtighten.
Image: Wet Sounds REV 10 Tower Speakers shown with silver fixed clamps.
Image: Detailed view of the silver fixed clamps, showing internal wiring pathways.
Image: Disassembled components of a silver fixed clamp, illustrating its construction.
Wiring Connections
The REV 10 speakers require connection to an appropriate marine amplifier. Ensure the amplifier can provide sufficient power (300 Watts RMS per speaker) and is compatible with a 4-ohm impedance load.
- Route the speaker wires from the speakers to the amplifier, ensuring they are protected from abrasion and moisture.
- Connect the positive (+) and negative (-) terminals of each speaker to the corresponding output channels on your amplifier.
- Ensure correct polarity for all connections. Incorrect polarity can lead to reduced sound quality and performance.
- If wiring multiple speakers or a subwoofer, consult your amplifier's manual for parallel or series wiring configurations to match the system's optimal impedance.
- After all connections are made, secure any loose wiring and test the system at a low volume.
Operating Instructions
Once properly installed and connected to an amplifier and audio source, your Wet Sounds REV 10 speakers are ready for use.
- Power On: Turn on your marine audio system, including the amplifier and head unit.
- Source Selection: Select your desired audio source (e.g., radio, Bluetooth device, media player) from your head unit.
- Volume Adjustment: Start with the volume at a low level and gradually increase it to your preferred listening level. Avoid excessively high volumes to prevent speaker damage and hearing loss.
- Sound Optimization: Adjust the equalizer settings on your head unit or amplifier to optimize the sound for your environment and personal preference. The REV TEC technology is designed to provide clear sound even at a distance and off-axis.
- Voice Control: If your connected audio system supports voice control, the speakers will reproduce audio commands and responses.
Image: Front view of two Wet Sounds REV 10 speakers, showcasing the grille design.
Maintenance and Care
Regular maintenance will help prolong the life and performance of your Wet Sounds REV 10 speakers.
- Cleaning: Clean the speaker enclosures and grilles regularly with a soft, damp cloth. For stubborn dirt, use a mild soap solution. Avoid abrasive cleaners or solvents, as these can damage the finish.
- Inspection: Periodically inspect the mounting hardware and wiring connections for any signs of corrosion, looseness, or wear. Tighten any loose fasteners and address any corrosion promptly.
- Protection: While the speakers are waterproof, consider using protective covers when the vessel is stored for extended periods, especially in harsh environments.
- Winterization: If operating in cold climates, follow proper winterization procedures for your marine audio system to prevent damage from freezing temperatures.
Image: Side profile of a single Wet Sounds REV 10 speaker, highlighting its aerodynamic design.
Troubleshooting
If you experience issues with your speakers, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| No sound from speakers |
|
|
| Distorted or poor sound quality |
|
|
| Intermittent sound |
|
|
If these steps do not resolve the issue, contact Wet Sounds customer support or a qualified technician.
Warranty Information
Wet Sounds REV 10 speakers come with a limited warranty. For specific details regarding warranty coverage, terms, and conditions, please refer to the official Wet Sounds website or the warranty card included with your product. Retain your proof of purchase for warranty claims.
Customer Support
For further assistance, technical support, or to inquire about replacement parts, please visit the official Wet Sounds website or contact their customer service department.
