Introduction
Thank you for purchasing the HT Tiffany Style Table Lamp TJ1821. This manual provides essential information for the safe and proper assembly, operation, and maintenance of your new lamp. Please read these instructions carefully before use and retain them for future reference.
The HT Tiffany Style Table Lamp TJ1821, featuring its intricate stained glass shade and sturdy metal base.
Safety Instructions
- Always disconnect the power supply before cleaning, changing bulbs, or performing any maintenance.
- Do not use bulbs exceeding the specified wattage (E26X2, LED 5W-10W).
- Ensure the lamp is placed on a stable, level surface to prevent tipping.
- Keep the lamp away from water and moisture. This product is for indoor use only.
- Do not attempt to modify the lamp's electrical components. Refer servicing to qualified personnel.
- Handle the stained glass shade with care to prevent breakage.
Package Contents
Verify that all components are present and undamaged before assembly.
- Stained Glass Shade
- Metal Lamp Base with Sockets
- Finial (top decorative piece)
- Bulb (included)
The main components of the lamp: base, shade, and finial.
Setup
Follow these steps to assemble your lamp:
- Carefully unpack all components from the packaging.
- Place the metal lamp base on a stable, flat surface.
- Gently place the stained glass shade onto the lamp base, aligning the central hole of the shade with the threaded rod extending from the base.
- Screw the finial onto the threaded rod at the top of the shade until it is secure, but do not overtighten.
- Insert two E26 LED bulbs (5W-10W recommended) into the lamp sockets.
- Plug the power cord into a standard electrical outlet.
The lamp base showing the two E26 bulb sockets and pull chains for operation.
Operating
Your HT Tiffany Style Table Lamp features a double-coincidence switch system, including both an in-line switch on the cord and individual pull chains for each bulb.
- In-Line Switch: Use the switch located on the power cord to turn the entire lamp on or off.
- Pull Chains: Each of the two light sockets has an independent pull chain. Pulling a chain will turn its corresponding bulb on or off, allowing for flexible lighting control.
Video demonstrating the operation of the HT Tiffany Style Table Lamp, including turning it on and off and showcasing the illuminated shade.
The lamp fully illuminated, showcasing the intricate stained glass design.
Maintenance
Regular maintenance will help preserve the beauty and functionality of your lamp.
- Cleaning the Shade: Use a soft, dry cloth to gently wipe the stained glass shade. For stubborn dust, a slightly damp cloth can be used, followed immediately by a dry cloth. Avoid abrasive cleaners or harsh chemicals, as these can damage the glass or solder.
- Cleaning the Base: Wipe the metal base with a soft, dry cloth. Do not use polishing agents or abrasive materials that could scratch the finish.
- Bulb Replacement: Ensure the lamp is unplugged and the bulbs have cooled before attempting to replace them. Unscrew the old bulb and screw in a new E26 LED bulb (5W-10W).
Detail of the lamp's metal base, which should be cleaned with a soft, dry cloth.
Troubleshooting
If you encounter issues with your lamp, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Lamp does not turn on. | No power, loose bulb, faulty switch. | Check if the power cord is securely plugged in. Ensure the wall outlet has power. Tighten bulbs. Check both the in-line switch and pull chains. |
| Bulb flickers. | Loose bulb, incorrect bulb type/wattage, faulty wiring. | Tighten the bulb. Ensure the bulb wattage is within the recommended range (5W-10W LED). If flickering persists, try a different bulb. If the issue continues, consult a qualified electrician. |
| Shade appears unstable. | Finial not tightened, shade not seated correctly. | Ensure the finial is securely tightened. Re-seat the shade on the lamp base, ensuring it is level. |
Specifications
Key technical details for the HT Tiffany Style Table Lamp TJ1821:
| Feature | Detail |
|---|---|
| Model Number | TJ1821 |
| Product Dimensions | 18"D x 18"W x 26"H |
| Item Weight | 8 Kilograms (17.6 pounds) |
| Lamp Type | Table Lamp |
| Shade Material | Stained Glass (448 pieces of colored glass and 154 glass beads) |
| Base Material | Metal |
| Light Source Type | LED E26X2 |
| Recommended Wattage | 5W-10W per bulb |
| Number of Light Sources | 2 |
| Switch Type | In-Line and Pull Chain (double-coincidence switch) |
| Wire Length | 1.5 meters |
| Voltage | 110 Volts |
| Certification | UL Certified |
| Specific Uses | Indoor use only |
Warranty and Support
For warranty information or technical support, please refer to the retailer or manufacturer's official website. Keep your purchase receipt as proof of purchase.