1. Introduction
The Memphis Audio SE1040 10-inch Street Edge Single 4-Ohm Subwoofer is designed to deliver impressive bass performance for your vehicle's audio system. This manual provides essential information for proper installation, operation, and maintenance to ensure optimal performance and longevity of your subwoofer.
Key Features:
- Polypropylene SE branded cone for durability and sound quality.
- Rubber surround for enhanced excursion and longevity.
- 1.5-inch copper voice coil for efficient power handling.
- 27oz magnet for robust motor structure.
- DVVC Direct Vent Voice Coil Cooling for thermal management.
2. Safety Information
Please read all safety instructions before installing or operating your subwoofer. Failure to do so may result in injury or damage to the product or vehicle.
- Always disconnect the vehicle's battery negative terminal before beginning any electrical work.
- Ensure all wiring is properly insulated and secured to prevent short circuits and damage.
- Avoid mounting the subwoofer in locations where it may obstruct driver visibility or interfere with vehicle safety systems.
- Do not expose the subwoofer to excessive moisture or extreme temperatures.
- Use appropriate hearing protection when testing or operating the audio system at high volumes.
3. Package Contents
Verify that all items are present in the package:
- Memphis Audio SE1040 10" Subwoofer (Model: SE1040-UVG)
4. Setup and Installation
Proper installation is crucial for the performance and longevity of your subwoofer. If you are unsure about any part of the installation process, consult a professional car audio installer.
4.1 Mounting Considerations
The SE1040 subwoofer is designed for installation in a suitable enclosure (not included). The enclosure type (sealed, ported, bandpass) will significantly impact the subwoofer's performance characteristics. Refer to recommended enclosure specifications from Memphis Audio for optimal results.
- Ensure the mounting surface is rigid and free from vibrations.
- Allow adequate clearance around the subwoofer for proper air circulation and excursion.
- Secure the subwoofer firmly to the enclosure using appropriate screws and gaskets to prevent air leaks.
Figure 1: Angled view of the Memphis Audio SE1040 10-inch subwoofer, showcasing the cone and surround.
Figure 2: Top-down view of the Memphis Audio SE1040 10-inch subwoofer, highlighting the 'SE Street Edge' branding on the cone.
4.2 Wiring Connections
The SE1040 is a single 4-Ohm subwoofer. Connect the subwoofer to a compatible amplifier that can safely operate at a 4-Ohm load. Ensure correct polarity (+ to + and - to -) to avoid phase issues and ensure optimal sound reproduction.
- Use high-quality speaker wire of appropriate gauge for the power level and distance.
- Strip wire ends carefully and ensure no stray strands can cause short circuits.
- Securely connect wires to the subwoofer's push terminals.
Figure 3: Side view of the Memphis Audio SE1040 10-inch subwoofer, showing the rear magnet structure and speaker wire terminals.
5. Operation
Once installed, the subwoofer operates as part of your vehicle's overall audio system. Proper amplifier settings and head unit adjustments are essential for optimal performance.
5.1 Amplifier Matching
Ensure your amplifier's RMS power output matches the subwoofer's RMS power handling (200 watts). Overpowering or underpowering can lead to damage or poor performance.
5.2 Initial Sound Adjustment
- Start with the amplifier's gain control at its minimum setting.
- Play a familiar piece of music with strong bass content.
- Slowly increase the amplifier's gain until the subwoofer blends seamlessly with the rest of your audio system without distortion.
- Adjust the low-pass filter (LPF) on your amplifier or head unit to prevent the subwoofer from playing frequencies it is not designed for, typically between 80Hz and 120Hz.
6. Maintenance
The Memphis Audio SE1040 subwoofer requires minimal maintenance to ensure long-term performance.
- Periodically inspect the subwoofer cone and surround for any signs of damage or wear.
- Keep the subwoofer free from dust and debris. Use a soft, dry cloth for cleaning.
- Ensure all wiring connections remain secure.
7. Troubleshooting
If you experience issues with your subwoofer, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| No sound from subwoofer | No power to amplifier; loose wiring; amplifier in protect mode; incorrect head unit settings. | Check amplifier power and ground connections. Verify remote turn-on wire. Inspect all speaker wires. Check amplifier fuses. Adjust head unit settings (subwoofer output, volume). |
| Distorted or unclear bass | Amplifier gain set too high; incorrect LPF setting; damaged subwoofer; poor enclosure. | Reduce amplifier gain. Adjust LPF. Inspect subwoofer cone and surround for damage. Ensure enclosure is sealed and properly constructed. |
| Subwoofer cuts out intermittently | Loose wiring; amplifier overheating; impedance mismatch. | Check all wiring connections. Ensure amplifier has adequate ventilation. Verify amplifier is stable at the subwoofer's 4-Ohm impedance. |
8. Specifications
Detailed technical specifications for the Memphis Audio SE1040 10" Street Edge Single 4-Ohm Subwoofer:
| Specification | Value |
|---|---|
| Model Name | SE1040 |
| Speaker Type | Subwoofer |
| Recommended Uses For Product | Vehicle |
| Subwoofer Diameter | 10 Inches |
| Unit Count | 1.0 Count |
| Included Components | SE1040-UVG |
| Product Dimensions | 6.3"D x 11.61"W x 5.3"H |
| Item Weight | 7.7 Pounds |
| Impedance | 4 Ohm |
| Number of Items | 1 |
| Speaker Size | 10 Inches |
| Power Source | Corded Electric (for amplifier connection) |
| Woofer Diameter | 10 Inches |
| Vehicle Service Type | SUVs, Select Cars, Truck |
| Audio Driver Size | 10 Inches |
| UPC | 702588210085 |
| Manufacturer | Memphis Audio |
| Speaker Maximum Output Power | 200 Watts RMS / 400 Watts Peak |
| Connectivity Technology | Auxiliary, RCA (via amplifier) |
| Mounting Type | Flush Mount |
9. Warranty Information
Memphis Audio products are designed and manufactured to the highest quality standards. This product is covered by a manufacturer's warranty against defects in materials and workmanship. The specific terms and duration of the warranty may vary by region and retailer. Please retain your proof of purchase for warranty claims. For detailed warranty information, please contact Memphis Audio customer support or refer to the warranty card included with your product, if applicable.
10. Customer Support
For further assistance, technical support, or inquiries regarding your Memphis Audio SE1040 subwoofer, please contact Memphis Audio directly.
- Manufacturer: Memphis Audio
- Online Store: Visit the Memphis Audio Store on Amazon
