Yale Vertical Applied Tilting Lock for Profile Cylinder

Introduction

This manual provides comprehensive instructions for the installation, operation, and maintenance of your Yale Vertical Applied Tilting Lock for Profile Cylinder, Model Y9B03415. Please read these instructions carefully before installation and use to ensure proper function and safety.

Safety Information

• Always wear appropriate personal protective equipment (PPE) during installation, such as safety glasses and gloves.
• Ensure all tools are in good working condition before use.
• Keep small parts away from children to prevent choking hazards.
• Do not attempt to modify the lock mechanism, as this may compromise its security and void the warranty.
• If you are unsure about any step, consult a qualified locksmith or professional installer.

Package Contents

Verify that all components are present before beginning installation:

• 1 x Yale Vertical Applied Tilting Lock unit
• 1 x Profile Cylinder (if included with the lock)
• 3 x Keys (Model 01009001)
• Mounting screws and hardware (not explicitly listed but implied for installation)

Note: The profile cylinder and keys are typically included as part of the lock assembly.

Specifications

Setup and Installation

This section guides you through the process of installing the Yale Vertical Applied Tilting Lock. Ensure you have the necessary tools, including a drill, screwdriver, measuring tape, and pencil.

1. Prepare the Door/Gate

Identify the desired mounting location on your tilting door or gate. The lock is designed for vertical application. Ensure the surface is clean and free from obstructions.

2. Mark Drilling Points

Use the provided technical drawing as a guide to mark the drilling points for the lock body and the profile cylinder. Precision is crucial for proper alignment.

Technical drawing illustrating the precise dimensions and mounting points for the Yale Vertical Applied Tilting Lock. Key measurements include overall height (192mm), width (55mm), and distances for the cylinder (70mm from top mounting hole) and keyhole (36mm from bottom edge).

1. Measure and mark the center point for the profile cylinder.
2. Mark the four mounting screw holes for the lock body, referring to the 192mm height and 55mm width.
3. Mark the hole for the square spindle (Quadro 8) if applicable for your cylinder type.

3. Drill Holes

Carefully drill pilot holes at the marked points. Ensure the drill bit size is appropriate for your mounting screws and the material of your door/gate.

4. Mount the Lock Body

Position the lock body onto the door/gate, aligning the holes. Secure it using the provided mounting screws. Do not overtighten.

5. Install the Profile Cylinder

Insert the profile cylinder into its designated opening in the lock body. Secure it with the cylinder screw, typically located on the side of the lock body.

Image of the Yale Vertical Applied Tilting Lock, highlighting its satin/nickel-plated finish and the integrated profile cylinder. This view shows the complete assembly ready for installation.

6. Install the Strike Plate (if applicable)

If your installation requires a strike plate for the tilting bolt, mark and install it on the door frame or opposing surface, ensuring proper alignment with the lock's bolt.

7. Test Functionality

Before closing the door/gate, test the lock's operation with the key. Ensure the bolt extends and retracts smoothly without obstruction. Close the door/gate and test locking and unlocking from both sides (if applicable).

Operating Instructions

Locking the Door/Gate

1. Ensure the door or gate is fully closed and aligned with the strike plate.
2. Insert the key into the profile cylinder.
3. Turn the key to extend the tilting bolt into the strike plate.
4. Remove the key. The door/gate is now locked.

Unlocking the Door/Gate

1. Insert the key into the profile cylinder.
2. Turn the key in the opposite direction to retract the tilting bolt.
3. Remove the key and open the door/gate.

Maintenance

Regular maintenance ensures the longevity and smooth operation of your Yale lock.

• Cleaning: Wipe the lock body with a soft, damp cloth. Avoid abrasive cleaners or solvents that could damage the finish.
• Lubrication: Periodically apply a small amount of graphite-based lubricant or a specialized lock lubricant into the keyway of the cylinder. Do not use oil-based lubricants, as they can attract dust and grime.
• Inspection: Regularly check all mounting screws for tightness. Inspect the lock for any signs of wear, damage, or misalignment.
• Key Care: Do not force the key if it feels stiff. Ensure keys are not bent or damaged.

Troubleshooting

Warranty and Support

Yale products are manufactured to high standards and undergo rigorous testing. For specific warranty details, please refer to the documentation provided at the time of purchase or visit the official Yale website.

If you encounter any issues not covered in this manual or require further assistance, please contact Yale customer support. Contact information can typically be found on the Yale website or product packaging.

For privacy and legal information, you may visit: Yale Privacy and Legal Center