1. Introduction
This manual provides essential information for the safe and effective use of your Sealey S01182 #3 x 150mm Phillips Screwdriver. Designed for light craft and DIY applications, this tool features a durable construction and ergonomic design for comfortable and efficient use. Please read these instructions carefully before using the screwdriver and retain them for future reference.
2. Product Features
- Chrome Vanadium Shaft: The shaft is constructed from high-grade Chrome Vanadium steel, known for its strength and durability.
- Satin Finish: The shaft features a satin finish, providing corrosion protection and resistance to scratches and fingerprints, while also improving grip.
- Shot-Blasted and Magnetized Tip: The Phillips tip is shot-blasted for enhanced grip on fasteners and magnetized to securely hold screws, preventing drops.
- Contoured Soft-Grip Handle: The ergonomically designed handle offers a comfortable and secure grip, reducing hand fatigue during prolonged use.
- Color-Coded for Quick Identification: The handle is color-coded for easy identification of the screwdriver type (Phillips) and size.
Figure 2.1: Features of the satin finish shaft, including corrosion protection and improved grip.
3. Setup
The Sealey S01182 Phillips Screwdriver requires no assembly. It is ready for immediate use upon receipt.
- Inspection: Before each use, visually inspect the screwdriver for any signs of damage, such as a bent shaft, worn tip, or cracked handle. Do not use a damaged tool.
- Selection: Ensure you are using the correct size Phillips screwdriver (#3) for the fastener to prevent stripping the screw head or damaging the screwdriver tip.
Figure 3.1: The Sealey S01182 Phillips Screwdriver ready for use.
4. Operating Instructions
Follow these steps for safe and effective operation of your Phillips screwdriver:
- Positioning: Place the tip of the screwdriver into the corresponding Phillips head screw. Ensure the tip is fully seated in the screw head to prevent cam-out.
- Applying Pressure: Apply firm, downward pressure on the handle to keep the tip engaged with the screw.
- Turning: Rotate the handle clockwise to tighten the screw or counter-clockwise to loosen it. Maintain consistent downward pressure throughout the turning motion.
- Finishing: Stop turning once the screw is adequately tightened or loosened. Avoid over-tightening, which can strip the screw or damage the material.
Figure 4.1: Proper grip and angle for operating the screwdriver.
5. Maintenance
Proper maintenance will extend the life of your Sealey screwdriver:
- Cleaning: After each use, wipe the shaft and handle with a clean, dry cloth to remove dirt, grease, or debris. For stubborn grime, a mild detergent solution can be used, followed by thorough drying.
- Storage: Store the screwdriver in a dry environment, away from excessive moisture or corrosive chemicals, to prevent rust or material degradation. Keep it in a toolbox or on a tool rack to protect the tip from damage.
- Tip Condition: Regularly check the Phillips tip for wear. A worn or rounded tip can lead to stripped screws and reduced effectiveness. Replace the screwdriver if the tip is significantly damaged.
6. Troubleshooting
Most issues with a screwdriver are related to improper use or wear. Here are some common scenarios:
- Screw Head Stripping: If the screw head is stripping, ensure you are using the correct size Phillips screwdriver (#3) and applying sufficient downward pressure. A worn screwdriver tip can also cause stripping.
- Screwdriver Tip Slipping: This often indicates insufficient downward pressure, an incorrect screwdriver size, or a worn tip. Ensure the tip is fully engaged and replace the tool if the tip is damaged.
- Difficulty Turning: If a screw is difficult to turn, do not force it. This could indicate a rusted screw, cross-threading, or an obstruction. Consider using a penetrating oil for rusted screws or re-evaluating the fastener.
7. Specifications
| Specification | Detail |
|---|---|
| Brand | Sealey |
| Model Number | S01182 |
| Model Name | #3 x 150mm Phillips Screwdriver |
| Part Number | S01182 |
| Tip Type | Phillips (#3) |
| Shaft Length | 150 mm |
| Overall Dimensions (L x W x H) | 31.5 x 5 x 4 cm |
| Item Weight | 150 Grams |
| Material | Chrome Vanadium Steel (Shaft) |
| Batteries Required? | No |
| GTIN | 05054511508437 |
8. Warranty and Support
Sealey products are manufactured to high standards and, with proper use and maintenance, are designed for long-lasting performance. This product is covered by a Sealey Lifetime Guarantee.
For specific warranty terms and conditions, or for technical support, please refer to the official Sealey website or contact your authorized Sealey dealer. Keep your proof of purchase for warranty claims.
Figure 8.1: Sealey Lifetime Guarantee information.
