Introduction
Thank you for choosing the Makerfire 7.4V 600mAh 2S Lipo Battery. This high-performance lithium polymer battery is designed for micro FPV racing drones and quadcopters, offering a reliable power source with an XT30 connector. Please read this manual thoroughly before using the battery to ensure safe operation and optimal performance.
Important Safety Instructions
Lithium Polymer (LiPo) batteries are powerful and require careful handling. Failure to follow these safety guidelines can result in fire, personal injury, and property damage.
- Charging: Always use a LiPo-compatible balance charger. Never charge unattended. Charge on a non-flammable surface away from combustible materials. Ensure charging current and voltage settings match the battery specifications (7.4V, 2S, 600mAh).
- Discharging: Do not over-discharge the battery. Stop use immediately if the voltage drops below 3.0V per cell (6.0V for a 2S battery). Over-discharging can permanently damage the battery.
- Storage: Store LiPo batteries at room temperature in a fireproof container, away from direct sunlight, heat sources, and flammable materials. For long-term storage, charge or discharge the battery to a storage voltage of 3.8V per cell (7.6V for a 2S battery).
- Physical Damage: Inspect the battery for any signs of damage (swelling, punctures, leaks, bent connectors) before each use. Do not use a damaged battery.
- Temperature: Do not expose the battery to extreme temperatures. Avoid charging or discharging in temperatures below 0°C (32°F) or above 45°C (113°F).
- Disposal: Dispose of LiPo batteries responsibly according to local regulations. Never dispose of them in regular trash or by incineration.
- Children: Keep batteries out of reach of children.
Product Features
- High Capacity: 600mAh for extended flight times.
- Voltage: 7.4V (2S) for consistent power delivery.
- Discharge Rate: 50C continuous / 100C burst for demanding applications.
- Connector: XT30 plug for secure and efficient power connection.
- Balancer Connector: JST-XHR for precise cell balancing during charging.
- Lightweight Design: Optimized for micro FPV racing drones.
Specifications
Image: Makerfire 7.4V 600mAh 2S Lipo Battery with XT30 Plug, showing its overall design and connectors.
| Feature | Detail |
|---|---|
| Battery Capacity | 600 mAh |
| Battery Voltage | 7.4V (2S) |
| Discharge Rate | 50C (Continuous) / 100C (Burst) |
| Connector Type | XT30 Plug |
| Cells Configuration | 2S1P |
| Balancer Connector | JST-XHR |
| Weight | Approximately 33.28g (1.17 oz) |
| Dimensions (L x W x H) | 62mm x 16mm x 14mm (2.44 x 0.63 x 0.55 inches) |
| Wire Gauge | 18AWG Silicone Wire |
Image: Detailed dimensions of the Makerfire 7.4V 600mAh 2S Lipo Battery, showing length, width, and height measurements.
Image: The Makerfire 7.4V 600mAh 2S Lipo Battery being weighed on a digital scale, displaying approximately 33.28 grams.
Setup
1. Initial Charging
Before first use, fully charge the battery using a compatible LiPo balance charger. Ensure the charger is set to the correct voltage (7.4V or 2S) and capacity (600mAh) for this battery. Always monitor the charging process.
Image: Close-up view of the battery's components, highlighting the 18AWG Silicone Wire, XT30 Plug, and JST-XHR balancer connector.
2. Installation in Device
Carefully connect the XT30 plug of the battery to the corresponding connector on your micro FPV racing drone or quadcopter. Ensure the JST-XHR balance lead is not pinched or damaged during installation. Secure the battery within the device to prevent movement during operation.
Image: Diagram illustrating the compatibility of the 600mAh 2S Lipo Battery with several micro FPV drones and quadcopters.
Operating Instructions
- Pre-Flight Check: Always check the battery voltage before each flight to ensure it is fully charged and healthy.
- Connection: Connect the battery to your device's power input. Ensure a firm connection.
- Monitoring: During operation, monitor the battery voltage, especially if your device has telemetry. Stop flying when the battery reaches its minimum safe voltage (6.0V for 2S) to prevent over-discharge.
- Disconnection: After use, disconnect the battery from the device.
Maintenance and Storage
- Regular Inspection: Periodically inspect the battery for any signs of swelling, damage to the casing, or connector issues.
- Cleaning: Keep the battery and connectors clean and free from dirt or debris.
- Long-Term Storage: If storing the battery for more than a few days, charge or discharge it to a storage voltage of 3.8V per cell (7.6V for a 2S battery). This helps prolong battery life.
- Storage Environment: Store batteries in a cool, dry place, ideally in a fireproof LiPo bag or container, away from direct sunlight and extreme temperatures.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Battery not charging | Incorrect charger settings; damaged charger or battery; poor connection. | Verify charger settings (LiPo, 2S, 7.4V, 600mAh); check all connections; inspect battery for damage. If damaged, discontinue use. |
| Short flight times | Battery degradation; over-discharge; high power consumption by device. | Ensure battery is fully charged; avoid over-discharging; consider device power draw. Replace battery if degradation is significant. |
| Battery swelling | Overcharging; over-discharging; physical damage; internal short circuit. | Immediately discontinue use. Swelling indicates a dangerous condition. Safely dispose of the battery. |
Warranty and Support
For warranty information or technical support regarding your Makerfire 7.4V 600mAh 2S Lipo Battery, please contact Makerfire customer service through their official website or the retailer from whom you purchased the product. Please have your purchase details and product model information ready.
