CLEANmaxx 476 Cordless Vibrating Floor Mop User Manual

1. Introduction

Thank you for choosing the CLEANmaxx 476 Cordless Vibrating Floor Mop. This manual provides essential information for the safe and efficient operation, maintenance, and care of your new appliance. Please read these instructions thoroughly before first use and keep them for future reference.

2. Safety Instructions

To prevent injury or damage, please observe the following safety precautions:

• This appliance is intended for household use only. Do not use it for commercial purposes.
• Keep the appliance out of reach of children and pets.
• Do not immerse the main unit in water or other liquids.
• Use only the original power adapter supplied with the device for charging.
• Do not operate the appliance if it is damaged or malfunctioning. Contact customer support for assistance.
• Ensure the water tank is filled with appropriate cleaning solution and water. Do not use corrosive or flammable liquids.
• Always switch off the appliance and disconnect it from the power supply before cleaning or maintenance.
• The battery is integrated and not user-replaceable. Do not attempt to open the battery compartment.

3. Package Contents

Please check that all items are present and undamaged:

• 1x CLEANmaxx 476 Mop Head with integrated battery
• 1x Handle (3 parts for assembly)
• 1x Power Adapter/Charger
• 2x Microfiber Cleaning Cloths
• 1x Measuring Cup

Figure 1: All components included in the CLEANmaxx 476 package.

4. Setup and Initial Use

4.1 Assembling the Handle

1. Connect the three handle parts by twisting them together until they are securely fastened.
2. Attach the assembled handle to the main mop head unit. Ensure it clicks into place.

4.2 Attaching the Microfiber Cloths

1. Place the mop head on a flat surface.
2. Align the microfiber cleaning cloths with the hook-and-loop fasteners on the underside of the mop head.
3. Press the cloths firmly onto the fasteners to secure them.

Figure 2: Securing the microfiber cleaning cloths to the mop head.

4.3 Charging the Battery

1. Before first use, fully charge the mop's integrated lithium-ion battery.
2. Connect the power adapter to the charging port on the mop head and then to a power outlet.
3. The LED indicator lights on the mop head will show the charging status. A full charge typically takes approximately 2.5 hours.
4. Once fully charged, disconnect the adapter. The mop provides up to 50 minutes of active runtime on a full charge.

4.4 Filling the Water Tank

1. Locate the water tank cap on the mop head.
2. Open the cap and use the provided measuring cup to fill the 230 ml tank with clean water and your preferred floor cleaning solution. Do not overfill.
3. Securely close the water tank cap.

5. Operating Instructions

5.1 Powering On/Off

• To turn on the mop, press the power button located on the handle. The mop will begin vibrating.
• To turn off the mop, press the power button again. The mop will automatically switch off if held vertically for a few seconds.

Figure 3: Location of the power button on the handle.

5.2 Using the Spray Function

• While the mop is powered on, press the spray button on the handle to dispense cleaning solution onto the floor.
• Release the button to stop spraying.

Figure 4: Mop spraying cleaning solution during use.

5.3 Using the LED Light

• The integrated LED light automatically illuminates when the mop is in operation, providing visibility in dark areas or under furniture.

Figure 5: LED light illuminating the cleaning path under furniture.

Figure 6: The mop head with its LED light activated.

5.4 Cleaning Technique

• Guide the mop across the floor with gentle pressure. The vibrating function assists in effortless cleaning.
• Use the spray function as needed to moisten the floor.
• The mop is designed for various hard floor surfaces.

6. Maintenance and Care

6.1 Cleaning the Microfiber Cloths

• After each use, remove the microfiber cloths from the mop head.
• The cloths are machine washable at a low temperature (e.g., 30°C) without fabric softener.
• Allow them to air dry completely before reattaching or storing.

6.2 Emptying and Cleaning the Water Tank

• After each use, empty any remaining liquid from the water tank.
• Rinse the tank with clean water to prevent residue buildup.
• Allow the tank to air dry before closing the cap.

6.3 Cleaning the Mop Head

• Wipe the exterior of the mop head with a damp cloth. Do not use abrasive cleaners or immerse the unit in water.

6.4 Storage

• Store the mop in a dry place, away from direct sunlight and extreme temperatures.
• Ensure the battery is partially charged if storing for extended periods to maintain battery health.

7. Troubleshooting

If the problem persists after attempting these solutions, please contact customer support.

8. Technical Specifications

• Model Number: 476
• Brand: CLEANmaxx
• Dimensions (L x W x H): 40.01 x 35.99 x 11.99 cm
• Weight: 3.6 kg
• Voltage: 240 Volts (Charger Input)
• Battery: Integrated Lithium-ion, 2000mAh
• Runtime: Up to 50 minutes
• Water Tank Capacity: 230 ml
• Handle Material: Aluminum
• Mop Head Material: Microfiber
• Features: Cordless, Vibrating Function, Spray Function, LED Light

9. Warranty and Customer Support

This CLEANmaxx product is covered by a standard manufacturer's warranty. Please refer to the warranty card included in your package for specific terms and conditions.

For technical assistance, spare parts, or warranty claims, please contact your retailer or the CLEANmaxx customer service department. Contact information can typically be found on the product packaging or the official CLEANmaxx website.