Type S Portable Car Jump Starter Instruction Manual

1. Introduction

This manual provides detailed instructions for the safe and effective use of your Type S Portable Car Jump Starter. This device is designed to jump-start 12V vehicles, serve as a portable power bank, and provide emergency lighting. Please read this manual thoroughly before operation and retain it for future reference.

2. Safety Information

WARNING: Improper use can result in injury or damage. Always follow these safety guidelines.

• Ensure the jump starter is fully charged before use.
• Do not attempt to jump-start vehicles with voltage systems other than 12V.
• Avoid short-circuiting the jumper clamps. Do not connect the red and black clamps together.
• Keep the device away from moisture, heat, and flammable materials.
• Do not disassemble or modify the unit. Refer all servicing to qualified personnel.
• Wear eye protection when working with car batteries.
• This jump starter features UL certification (E482421) and advanced protection against reverse polarity, sparks, over-discharge, overheating, and short-circuits.

3. What's in the Box

The image shows the Type S Portable Car Jump Starter unit in blue, along with the red and black jumper cables. This is the main product and its essential accessory for jump-starting vehicles.

• 1 x 12V Jump Starter Power Bank
• 1 x Storage Bag
• 1 x 12V USB Car Charger
• 1 x Micro USB Charging Cable
• 1 x Jumper Cable with Smart & Safe Protection

4. Product Overview

This image highlights the key features of the jump starter: Dual USB-A Ports for charging devices, 350A Peak Current for jump-starting, a Multimode LED Flashlight for illumination, and built-in Safety Features for user protection.

The Type S Portable Car Jump Starter is a multi-functional device featuring:

• Jump Start Port: For connecting the smart jumper cables.
• Dual USB-A Ports: For charging mobile devices (2.4A + 2.1A).
• LED Flashlight: With solid, strobe, and SOS modes.
• Battery Level Indicator: Displays the remaining charge.
• Power Button: To turn the unit on/off and cycle through flashlight modes.

5. Setup and Charging

5.1 Initial Charge

Before first use, fully charge the jump starter. Connect the Micro USB Charging Cable to the jump starter's input port and the other end to the 12V USB Car Charger or any standard USB wall adapter (not included). The battery level indicator lights will illuminate during charging and turn solid when fully charged.

5.2 Maintaining Charge

For optimal performance, it is recommended to recharge the jump starter every 3-6 months, even if not used, to maintain battery health.

6. Operating Instructions

6.1 Jump Starting a Vehicle

This image illustrates the Type S Jump Starter connected to a car battery, with the red clamp on the positive terminal and the black clamp on the negative terminal, ready to jump-start the vehicle. It also shows icons for car, SUV, and truck, indicating compatibility.

1. Ensure the jump starter has sufficient charge (at least 3 indicator lights).
2. Connect the smart jumper cable's blue plug into the jump start port on the jump starter.
3. Connect the red (+) clamp to the positive (+) terminal of the vehicle's battery.
4. Connect the black (-) clamp to the negative (-) terminal of the vehicle's battery.
5. Once connected, the indicator light on the smart cable will turn green, indicating a safe connection. If it's red or flashing, check connections or refer to troubleshooting.
6. Start the vehicle's engine.
7. Once the vehicle starts, immediately disconnect the black (-) clamp, then the red (+) clamp, and finally disconnect the smart cable from the jump starter.
8. Do not crank the engine for more than 3 seconds. If the engine does not start, wait at least 30 seconds before attempting again.

6.2 Using as a Power Bank

This image shows the Type S Jump Starter with its dual USB-A ports, indicating its capability to charge compatible devices like phones, tablets, and headphones. A smartphone is shown connected and charging.

The jump starter features two USB-A output ports (2.4A and 2.1A) to charge your electronic devices.

1. Connect your device's USB charging cable to one of the USB-A output ports on the jump starter.
2. The jump starter will automatically begin charging your device.
3. Disconnect your device once charging is complete.

6.3 Using the LED Flashlight

This image displays the Type S Jump Starter with its built-in LED flashlight turned on, illuminating the area in front of it. This highlights its utility as an emergency light source.

The built-in LED flashlight has multiple modes for various situations.

1. Press and hold the power button for 3 seconds to turn on the flashlight (solid mode).
2. Press the power button once more to switch to Strobe mode.
3. Press the power button again to switch to SOS mode.
4. Press and hold the power button for 3 seconds to turn off the flashlight.

7. Maintenance

• Clean the unit with a dry, soft cloth. Do not use abrasive cleaners or solvents.
• Store the jump starter in a cool, dry place, away from direct sunlight and extreme temperatures.
• Ensure the unit is fully charged before storing for extended periods. Recharge every 3-6 months.
• Keep the jumper clamps clean and free of corrosion.

8. Troubleshooting

9. Specifications

10. Warranty and Support

TYPE S TOURING ITEMS is committed to providing quality products. For support and warranty information:

• Extended Warranty: Register your product online for extended warranty benefits.
• Customer Care: Contact our US-based customer care hotline for assistance.
• Installation Videos: Visit our YouTube channel for helpful installation and usage videos.
• For further assistance, please refer to the contact information provided with your product packaging or visit the official TYPE S website.