Introduction
This manual provides instructions for the UpStart Components Universal Remote Control, Model RC-RCR503BZ. This remote is designed as a replacement for various devices, including RCA 3-Device Universal Remote Controls, and is compatible with Sanyo TVs using specific remote codes. It allows you to control multiple entertainment devices from a single unit.
Please note that this is an UpStart Components Brand replacement part and not an OEM product. All mentions of brand names or model descriptions are made strictly to illustrate compatibility. This product is not affiliated with any original manufacturers.
Setup
1. Battery Installation
The remote control requires two (2) AAA batteries (not included). Follow these steps to install them:
- Locate the battery compartment cover on the back of the remote control.
- Press down on the tab and slide the cover off.
- Insert two AAA batteries, ensuring the positive (+) and negative (-) terminals match the diagrams inside the compartment.
- Slide the battery compartment cover back into place until it clicks securely.
Image: Front view of the UpStart Components Universal Remote Control. This image shows the layout of all buttons, including the power, channel, volume, number pad, and playback controls.
2. Programming the Remote Control
This universal remote can control up to three devices. To program the remote for your specific devices (e.g., TV, SAT/CBL/DTC, DVD/VCR), you will need to enter a 4-digit code. The remote includes a "CODE SEARCH" function to assist with this process.
Example for Sanyo TV: Use remote codes such as 0054 or 1142.
General Programming Steps (refer to your device's manual for specific codes if not listed here):
- Turn on the device you wish to control (e.g., your Sanyo TV).
- On the universal remote, press and hold the desired device button (e.g., TV, SAT-CBL-DTC, or DVD-VCR) for approximately 3 seconds until the indicator light (usually the POWER button) illuminates.
- While holding the device button, enter the 4-digit code for your device (e.g., 0054 for Sanyo TV).
- Release the device button. The indicator light should turn off, indicating the code has been accepted.
- Test the remote by pressing the POWER button. If the device turns off, the programming was successful.
- If the device does not respond, repeat the steps with a different code from your device's manual or use the Code Search method below.
3. Code Search Method
If you cannot find a suitable code, use the Code Search function:
- Turn on the device you wish to control.
- Press and hold the CODE SEARCH button until the indicator light illuminates.
- Press and release the desired device button (e.g., TV). The indicator light will blink once and then remain lit.
- Point the remote at the device and repeatedly press the POWER button (or CHAN+ for TVs) until the device turns off. Pause briefly between presses to allow the device to respond.
- Once the device turns off, immediately press the ENTER button to save the code. The indicator light will turn off.
- Test the remote's functions. If some functions do not work, you may need to repeat the Code Search process to find a more compatible code.
Operating the Remote Control
Once programmed, the remote control functions similarly to your original device remote. Ensure the remote is pointed directly at the device's infrared sensor.
Image: Angled view of the UpStart Components Universal Remote Control. This perspective highlights the ergonomic design and button placement.
Key Functions:
- POWER: Turns the selected device on or off.
- Device Buttons (TV, SAT-CBL-DTC, DVD-VCR): Selects the device you wish to control.
- VOL+/-: Adjusts the volume of the selected device.
- CHAN+/-: Changes channels on the selected device.
- MUTE: Silences the audio.
- Number Pad (0-9): Direct channel entry or menu navigation.
- MENU: Accesses the device's main menu.
- GO BACK: Returns to the previous screen or channel.
- SOURCE: Cycles through input sources (e.g., HDMI 1, HDMI 2).
- Directional Pad (Up, Down, Left, Right) & ENTER: Navigates menus and confirms selections.
- SLEEP: Activates the sleep timer function on compatible devices.
- Playback Controls (REW, PLAY, FWD, REC, PAUSE II, STOP): Controls media playback on compatible devices like DVD players or VCRs.
Maintenance
Battery Replacement
Replace batteries when the remote's indicator light becomes dim or the remote becomes unresponsive. Always replace both batteries at the same time with new AAA alkaline batteries. Do not mix old and new batteries, or different types of batteries.
Cleaning
To clean the remote control, wipe it with a soft, dry cloth. Do not use liquid cleaners or abrasive materials, as these can damage the remote's surface or internal components.
Troubleshooting
- Remote not working after programming:
- Ensure fresh batteries are correctly installed.
- Verify that the remote is pointed directly at the device's IR sensor.
- Try a different code for your device, or use the Code Search method again.
- Make sure you have selected the correct device button (TV, SAT-CBL-DTC, DVD-VCR) on the remote.
- Some buttons do not work:
- The current code may not be fully compatible with all functions of your device. Try using the Code Search method again to find a more comprehensive code.
- Ensure the remote is in the correct device mode (e.g., TV mode for TV functions).
- Indicator light does not illuminate:
- Check battery installation and replace batteries if necessary.
Specifications
| Feature | Detail |
|---|---|
| Model Number | RC-RCR503BZ |
| Batteries Required | 2 AAA batteries (not included) |
| Connectivity Technology | Infrared (IR) |
| Compatible Devices | Television, Satellite/Cable/DTC, DVD/VCR |
| Color | Black |
| Manufacturer | UpStart Components |
Warranty
This product is offered by UpStart Components. Any warranties for this product are provided solely by UpStart Components. This replacement part is not covered under any warranties offered by the original manufacturers of the devices it is compatible with.
For specific warranty details, please refer to the documentation provided at the time of purchase or contact UpStart Components directly.
Support
If you encounter issues not covered in this manual or require further assistance, please refer to the contact information provided by your retailer or UpStart Components at the time of purchase.
For general inquiries or to find additional support resources, you may visit the UpStart Components website (if available) or contact their customer service.
