1. Introduction
This manual provides instructions for the installation, operation, and maintenance of your SARTODOORS Planum 2102 Modern Solid French Door. This door features a white matte finish, frosted glass, and a solid pine wood core, designed for interior use in areas such as bedrooms, bathrooms, or closets. Please read these instructions thoroughly before beginning installation to ensure proper function and longevity of your door.
Image 1.1: The SARTODOORS Planum 2102 Modern French Door, White Matte.
2. Parts List
The SARTODOORS Planum 2102 door set includes the following components:
- Fully finished door slab with frosted glass (1 3/5" thick, solid pine wood core).
- Door frame components (suitable for wall thickness from 4" to 5").
- Trims (2.95" wide).
- Passage lever/knob (modern square style in Satin Nickel).
- Non-mortise butterfly hinges.
Image 2.1: Cross-section diagram illustrating the door's solid wood core, MDF sublayer, and glass panel with sealant.
3. Setup and Installation
The SARTODOORS Planum 2102 door is supplied with all necessary components for installation. The door is not pre-attached to the frame, allowing flexibility in choosing the swing direction during installation. Assembly of frames and trims is required.
3.1. Required Tools (Not Included)
- Measuring tape
- Level
- Drill
- Screwdriver
- Saw (if trimming is needed)
- Wood shims
- Construction adhesive or wood glue (for frame assembly)
3.2. Preparing the Rough Opening
Ensure your rough opening dimensions are appropriate for the door. For a 36" x 80" door, the recommended minimal rough opening is 38" wide by 81 1/2" high. This allows for proper clearance and adjustment.
Image 3.1: Diagram illustrating the recommended rough opening dimensions for door installation.
3.3. Frame Assembly
- Unpack all frame components (parts 'a' and 'b' as shown in Image 3.2).
- Connect the vertical frame pieces ('a') to the horizontal header piece ('b') to form the door frame. Use appropriate fasteners and adhesive for a secure connection.
- Ensure the frame is square and level before proceeding.
Image 3.2: Visual guide for assembling the door frame components.
3.4. Installing the Door Slab and Hardware
- Position the assembled frame into the rough opening. Use shims to ensure the frame is plumb, level, and square. Secure the frame to the wall studs.
- Attach the non-mortise butterfly hinges to the door slab and the door frame. These hinges do not require routing out slots for installation.
- Hang the door slab onto the hinges. Check for proper swing and clearance.
- Drill the necessary holes for the passage lever/knob into the door slab according to the hardware manufacturer's instructions. Install the lever/knob.
- Install the trims around the door frame to finish the installation.
Image 3.3: Example of a non-mortise butterfly hinge included with the door set.
4. Operation
The SARTODOORS Planum 2102 door operates as a standard hinged interior door. To open, turn the passage lever/knob and pull or push the door. To close, gently push the door until it latches. The frosted glass provides privacy while allowing light to pass through.
5. Maintenance
To ensure the longevity and appearance of your SARTODOORS Planum 2102 door, follow these maintenance guidelines:
- Cleaning the Door Slab: Wipe the eco-veneer smooth coating with a soft, damp cloth. Avoid abrasive cleaners or harsh chemicals, as these can damage the finish.
- Cleaning the Frosted Glass: Use a standard glass cleaner and a soft cloth. Do not spray cleaner directly onto the glass; apply it to the cloth first to prevent drips from affecting the door finish.
- Hardware Maintenance: Periodically check the tightness of all screws on hinges and the door handle. Lubricate hinges with a silicone-based spray if they begin to squeak.
- General Inspection: Regularly inspect the door and frame for any signs of wear, damage, or loose components. Address any issues promptly to prevent further problems.
6. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Door does not close properly or rubs against the frame. | Frame is not plumb or square; hinges are loose or misaligned. | Check frame for plumb and square using a level. Adjust shims as needed. Tighten hinge screws. If necessary, re-position hinges. |
| Door handle is loose or difficult to operate. | Mounting screws are loose; internal mechanism requires lubrication. | Tighten all visible screws on the handle assembly. Apply a small amount of lubricant to the moving parts of the handle mechanism. |
| Hinges squeak. | Lack of lubrication. | Apply a silicone-based lubricant to the hinge pins. |
| Frosted glass appears cloudy or stained. | Residue from cleaning products or environmental factors. | Clean with a dedicated glass cleaner and a microfiber cloth. Avoid harsh chemicals. |
7. Specifications
| Feature | Detail |
|---|---|
| Brand | SARTODOORS |
| Model Number | 2102 |
| Door Dimensions | 36" (Width) x 80" (Height) x 1.6" (Thickness) |
| Material | Solid Pine Wood Core, Eco-Veneer Finish, Frosted Glass |
| Color | White Matte |
| Item Weight | 75 Pounds |
| Assembly Required | Yes |
| Sound Attenuation | 30% noise reduction over standard doors (due to 1 3/5" solid composite wood construction) |
| UPC | 600434955619 |
8. Warranty and Support
8.1. Warranty Information
SARTODOORS products are manufactured to high-quality standards. For specific warranty details regarding your Planum 2102 door, please refer to the documentation included with your purchase or contact SARTODOORS customer service directly. Generally, manufacturing defects are covered for a limited period from the date of purchase.
8.2. Customer Support
If you encounter any issues during installation or operation, or if you have questions about your SARTODOORS Planum 2102 door, please contact SARTODOORS customer support. Contact information can typically be found on the packaging or the official SARTODOORS website.
