InvisiClean Aura II Air Purifier Instruction Manual

1. Introduction and Overview

The InvisiClean Aura II Air Purifier (Model IC-5018) is designed to significantly improve indoor air quality. This advanced 4-in-1 system combines a powerful H13 True HEPA filter, an activated carbon pre-filter, an optional ionizer, and a UV-C light to effectively capture and neutralize airborne particles, allergens, odors, and harmful microorganisms. Ideal for large rooms and bedrooms, it provides cleaner, fresher air for a healthier living environment.

Figure 1: Front view of the InvisiClean Aura II Air Purifier.

The unit features a low EMF radiation DC motor, offering double the air output with up to 82% less electricity consumption. It is CARB Certified and SGS Tested, proven to eliminate 99% of Influenza A H1N1 Virus, E. Coli Bacteria, Staph. Aureus Bacteria, and Aspergillus Mold from your air. Its quiet operation makes it suitable for any room, including nurseries.

2. Setup

Follow these steps to set up your InvisiClean Aura II Air Purifier:

1. Unpack the Unit: Carefully remove the air purifier from its packaging.
2. Access Filter Compartment: The front cover of the unit is held by magnets. Gently pull the front cover to open the filter compartment.
3. Remove Filter Packaging: Inside, you will find the combined H13 True HEPA and Activated Carbon Pre-Filter. Remove it from its protective plastic packaging.
4. Install Filter: Place the filter back into the unit, ensuring it is properly seated. The charcoal pre-filter side should face outwards (towards the front cover).
5. Close Cover: Securely close the front cover. The magnetic closure will hold it in place.
6. Plug In: Plug the power cord into a standard electrical outlet. The unit is now ready for operation.

3. Operating Instructions

The control panel is located on the top of the unit, featuring intuitive touch buttons and indicator lights.

Figure 2: Control panel with Power, Sleep Mode, Fan Speed, UV Light/Ionizer, and Timer buttons.

• Power Button (⏻): Press to turn the unit On or Off. The indicator light will illuminate when the unit is active.
• Fan Speed / Turbo Mode (✇): Cycle through four fan speeds: Low (I), Medium (II), High (III), and Turbo. Each press increases the fan speed. Turbo mode provides maximum air circulation for rapid purification.
• Sleep Mode (☾): Activates the quietest fan setting and dims all indicator lights for undisturbed sleep. Press again to exit Sleep Mode.
• UV-C Light / Ionizer (☀︎ 🌲): This button controls both the UV-C light and the ionizer. Press once for UV-C light, twice for Ionizer, three times for both, and four times to turn both off. The respective indicator lights will show which function is active.
• Timer (🕒): Set the operating duration for 2 hours, 4 hours, or 8 hours. The unit will automatically turn off once the set time has elapsed.

Figure 3: The 4-stage filtration process of the InvisiClean Aura II.

4. Maintenance

Regular maintenance ensures optimal performance and extends the lifespan of your air purifier.

Filter Replacement

The H13 True HEPA filter with Activated Carbon Pre-Filter should be replaced approximately every 6-12 months, depending on usage and air quality. The unit features a filter reset indicator light that will illuminate when it's time to replace the filter.

1. Turn Off and Unplug: Always turn off and unplug the air purifier before performing any maintenance.
2. Open Front Cover: Gently pull the magnetic front cover to open the filter compartment.
3. Remove Old Filter: Carefully pull out the old filter. Dispose of it properly.
4. Install New Filter: Insert a new InvisiClean Aura II replacement filter (IC-5120) into the unit, ensuring the charcoal pre-filter side faces outwards.
5. Close Cover: Close the front cover securely.
6. Reset Filter Indicator: With the unit powered on, press and hold the Power/Filter Reset button for 3-5 seconds until the filter reset light turns off. This indicates the filter timer has been reset.

Figure 4: Easy access design for filter maintenance.

Cleaning the Unit

Wipe the exterior of the air purifier with a soft, dry cloth. Do not use abrasive cleaners or solvents. For the pre-filter, you may gently vacuum it between replacements to extend its life, but do not wash it.

Figure 5: Internal view of the air purifier, highlighting the fan and filter area.

5. Troubleshooting

If your InvisiClean Aura II Air Purifier is not functioning as expected, please refer to these common troubleshooting tips:

• Unit Not Turning On: Ensure the power cord is securely plugged into a working electrical outlet. Check if the front cover is properly closed, as a safety switch prevents operation if it's open.
• Reduced Airflow/Effectiveness: The filter may be clogged. Check the filter indicator light. If illuminated, replace the filter. Even if not illuminated, a heavily used filter may require earlier replacement. Ensure the filter is free from plastic packaging.
• Unusual Noise: Check if the filter is correctly installed and seated. Ensure no foreign objects are obstructing the fan or air inlets/outlets.
• Odor Present: The activated carbon filter may be saturated. Replace the filter.
• Filter Reset Light Remains On: After replacing the filter, ensure you press and hold the Power/Filter Reset button for 3-5 seconds until the light turns off.

If the issue persists after trying these steps, please contact customer support.

6. Specifications

7. Warranty and Support

InvisiClean is a US-based company committed to designing high-quality household products. We strive to provide the best support to our customers.

For any questions, technical assistance, or warranty claims, please contact InvisiClean customer support. You can typically find contact information on the product packaging or the official InvisiClean website. InvisiClean products are designed with premium components for long-lasting, high-performance use.