Emtek Select Privacy Door Lever Instruction Manual

Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your Emtek Select Privacy Door Lever, Model 5212US19.LSUS19.KNUS19.LH. Please read these instructions thoroughly before beginning installation to ensure proper function and longevity of your door hardware.

Package Contents

Verify that all components are present before beginning installation. If any parts are missing or damaged, contact Emtek customer support.

• Exterior Lever Handle with Rosette
• Interior Lever Handle with Rosette
• Latch Mechanism
• Spindle
• Mounting Screws
• Privacy Pin/Emergency Release Tool
• Strike Plate
• Dust Box (optional)

Safety Information

• Always wear appropriate safety gear, such as gloves and eye protection, during installation.
• Ensure the door is properly supported and secured before removing existing hardware or drilling new holes.
• Keep small parts away from children to prevent choking hazards.
• Do not use power tools on high torque settings when tightening screws to avoid stripping or damaging the hardware.

Setup and Installation

The Emtek Select Privacy Door Lever is designed for easy installation. This model is specifically for Left Hand (LH) doors. Ensure your door's handing matches this requirement.

Tools Required:

• Phillips Head Screwdriver
• Measuring Tape
• Pencil
• Drill (if new holes are required)

Installation Steps:

1. Prepare the Door: Ensure the door is prepped with standard bore holes (typically 2-1/8 inch cross bore and 1 inch edge bore) and a backset of 2-3/8 inches or 2-3/4 inches.
2. Install the Latch Mechanism: Insert the latch mechanism into the edge bore hole of the door. Secure it with the provided screws. Ensure the bevel of the latch bolt faces the door frame.
3. Install Exterior Lever: Place the exterior lever assembly through the cross bore hole, ensuring the spindle receiver aligns with the latch mechanism.
4. Install Interior Lever: Slide the spindle through the latch mechanism and into the exterior lever's receiver. Position the interior lever assembly over the spindle and align the mounting posts.
5. Secure the Levers: Using the provided mounting screws, attach the interior and exterior lever assemblies together. Tighten screws evenly until snug, but do not overtighten.
6. Test Operation: Before closing the door, test the lever action and privacy function to ensure smooth operation.
7. Install Strike Plate: Mark and chisel out the door frame for the strike plate. Secure the strike plate with screws, ensuring the latch bolt engages smoothly.

Figure 1: Emtek Select Privacy Door Lever, showcasing the modern rectangular rosette and knurled lever design. This image illustrates the assembled product.

Operating Instructions

Standard Operation:

To open the door from either side, simply depress the lever handle. The latch bolt will retract, allowing the door to open.

Privacy Function (Trim Lock):

• To Lock: From the interior side of the door, locate the privacy button or turn-piece on the rosette. Engage it to lock the exterior lever, preventing entry from the outside.
• To Unlock: From the interior, disengage the privacy button or turn-piece. The exterior lever will now operate freely.
• Emergency Release: In case of an emergency or accidental lockout, an emergency release hole is located on the exterior rosette. Insert the provided privacy pin/emergency release tool into this hole and push firmly to unlock the door.

Maintenance

• Cleaning: Clean the lever and rosette surfaces with a soft, damp cloth. Avoid abrasive cleaners, solvents, or harsh chemicals, as these can damage the finish.
• Lubrication: Periodically, a small amount of graphite-based lubricant can be applied to the latch mechanism to ensure smooth operation. Do not use oil-based lubricants, as they can attract dust and grime.
• Tightening: Check mounting screws periodically and tighten if necessary to prevent wobbling or loose operation. Do not overtighten.

Troubleshooting

Problem: Lever is stiff or difficult to turn.

Solution: Check for proper alignment of the spindle and latch mechanism. Apply a small amount of graphite lubricant to the latch bolt. Ensure mounting screws are not overtightened.

Problem: Privacy function does not engage or disengage.

Solution: Verify that the privacy mechanism components are correctly installed and aligned. Ensure no debris is obstructing the privacy button or turn-piece. If the issue persists, re-check the installation steps.

Problem: Door does not latch properly.

Solution: Inspect the strike plate and latch bolt for obstructions or misalignment. Adjust the strike plate position if necessary to ensure the latch bolt fully extends into the strike plate opening.

Specifications

Warranty and Support

Specific warranty details for the Emtek Select Privacy Door Lever are not provided in this document. For warranty information, technical support, or to inquire about replacement parts, please contact Emtek directly through their official website or customer service channels. Retain your proof of purchase for warranty claims.