Important Safety Information
Please read all instructions and warnings carefully before using your FERRET Ice Shelter. Failure to follow these instructions may result in injury or damage to the product.
- Fire Safety: This tent is flame retardant, but it is not fireproof. Keep all flame and heat sources away from the tent fabric. Do not use open flames, heaters, or cooking equipment inside the tent.
- Ventilation: Ensure adequate ventilation when using the shelter, especially if using any fuel-burning devices (not recommended). Carbon monoxide can be deadly.
- Anchoring: Always secure the tent with ice anchors and guy ropes, especially in windy conditions, to prevent it from blowing away or collapsing.
- Assembly: Exercise caution during setup and takedown to avoid pinching fingers or damaging the frame.
- Weather Conditions: Do not use the tent in extreme weather conditions beyond its design capabilities, such as severe storms or excessively high winds.
Package Contents
Verify that all components are present before proceeding with setup.
- 1 x Ice Shelter Tent
- 8 x Ice Anchors
- 4 x Two-meter Guy Ropes
- 7 x Transparent PVC Windows
- 1 x Carrier Bag (44 inches long)
Figure 1: Included Accessories. This image displays the carry bag, six transparent PVC windows, four two-meter guy ropes, and eight ice anchors.
Setup Instructions
The FERRET Ice Shelter features a pop-up design for quick and easy assembly.
- Unpack: Remove the shelter from its carrier bag and lay it flat on the ground.
- Top Hub: Locate the top hub. Unfold the blind by pulling the top hub upwards, allowing the corners to fall into place.
- Sidewall Hubs: Locate the web handles on each side wall. Pull each web handle firmly outwards to engage the sidewall hubs. Ensure all four sidewall hubs are fully extended.
- Secure: For stability, especially in windy conditions, use the provided ice anchors and guy ropes. There are 4 reserved holes at each corner and 5 web handles on each side for securing.
Figure 2: Setup and Takedown Diagram. This diagram visually guides you through unfolding the tent (steps 1-3) and collapsing it (step 4).
Operating Features
Your FERRET Ice Shelter is designed with several features to enhance your ice fishing experience.
- Doors: The shelter includes 1 zipped door for easy entry and exit. The door can be fixed open using the integrated fasteners.
- Windows: The design features 7 Velcro abreast double-windows. One layer is oxford fabric, and the other is transparent PVC. These windows allow for broad vision and can be opened or fully removed for additional venting. To attach, first stick on the plastic windows, then secure the Velcro shades.
- Air Vents: Two air vents are integrated to ensure adequate ventilation within the shelter.
- Internal Pockets: Two pockets are located inside the shelter for storing necessary ice fishing gear.
Figure 3: Exterior Features. This image points out the air vents, web handles, corner holes for anchoring, double-windows, and zipped doors.
Figure 4: Interior Features. This image provides an inside view, detailing the reserved holes (A), door (B), and double-windows (C).
Takedown Instructions
To collapse the shelter for storage:
- Release Anchors: Disengage all ice anchors and guy ropes.
- Collapse Sidewalls: Push firmly at the center of each sidewall hub to disengage them.
- Collapse Top: Push down firmly at the center of the top hub to collapse the tent.
- Fold and Store: Fold the tent neatly and place it back into the carrier bag.
Refer to Figure 2 for a visual guide on the takedown process (step 4).
Maintenance and Care
- Cleaning: The tent fabric is Oxford material. For cleaning, hand wash with mild soap and water. Do not use harsh detergents or bleach.
- Drying: Ensure the tent is completely dry before folding and storing to prevent mold and mildew growth.
- Storage: Store the tent in its carrier bag in a cool, dry place, away from direct sunlight and extreme temperatures.
- Inspection: Periodically inspect the fabric, zippers, hubs, and fiberglass poles for any signs of wear or damage. Repair minor tears promptly to prevent them from worsening.
- Window Care: The transparent PVC windows should be handled with care to avoid scratches or tears. Clean with a soft, damp cloth.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Tent is difficult to set up or take down. | New tent, stiff hubs; improper technique. | The hubs may be stiff initially. Practice setup and takedown a few times. Ensure you are pulling/pushing directly on the hubs/web handles. |
| Tent feels unstable or blows over easily. | Insufficient anchoring; strong winds. | Always use all provided ice anchors and guy ropes. Ensure anchors are securely drilled into the ice. Avoid using in excessively high winds. |
| Water leakage through seams or fabric. | Manufacturing defect; extreme weather; wear and tear. | Ensure all zippers are fully closed. For minor leaks, seam sealer can be applied. If leakage is significant or due to a defect, contact customer support. |
| Windows do not seal properly. | Improper attachment; Velcro misalignment. | Ensure the transparent PVC window layer is correctly aligned and pressed firmly onto its Velcro strips before attaching the outer fabric shade. |
Specifications
Figure 5: Product Dimensions. This image illustrates the overall size of the shelter.
| Feature | Detail |
|---|---|
| Model Number | BS-2-2 |
| Occupancy | 2 Person |
| Product Dimensions (L x W x H) | 58" x 58" x 66" |
| Floor Area | 23.36 square feet |
| Item Weight | 16 pounds |
| Material Type | Oxford Fabric, Fiberglass, Polyvinyl Chloride, Metal, Plastic |
| Water Resistance | Waterproof |
| Special Features | Lightweight, Pop Up, Portable, Waterproof, Windproof, Flame Retardant |
| Number of Doors | 1 |
| Number of Windows | 7 (Velcro abreast double-windows) |
| Color | Red |
Warranty and Support
For warranty information, product support, or to inquire about replacement parts, please contact FERRET customer service through the retailer where the product was purchased or visit the official FERRET brand store online.
Keep your purchase receipt as proof of purchase for any warranty claims.