WAC Lighting Aether 2in Round Light Engine Trim & LED Instruction Manual

1. Introduction and Overview

The WAC Lighting Aether 2in Round Light Engine Trim & LED is a high-performance recessed downlight designed for various indoor and outdoor applications. Its ultra-low profile design allows for installation in tight plenum spaces. This manual provides essential information for the safe installation, operation, and maintenance of your lighting fixture.

Key Features:

• Available in Round, Square, Flangeless Invisible, Adjustable, and Wall Wash configurations.
• Designed for use with New Construction Housings: HR-2LED-H13A or HR-2LED-H13AC.
• Ultra-low profile design with a 2.5-inch housing height for 2-inch trims.
• Smooth and continuous dimming capability down to 1% with compatible dimmers (Electronic Low Voltage or 0-10V).
• High-powered, replaceable LED light engine with 2700K color temperature, 90 CRI, and 65,000 rated hours.

2. Safety Information

Please read and understand all instructions before beginning installation. Failure to follow these instructions may result in electric shock, fire, or other hazards that could cause property damage or personal injury.

• WARNING: Risk of electric shock. Disconnect power at the fuse or circuit breaker before installing or servicing.
• All electrical connections must be in accordance with local codes, ordinances, or the National Electric Code (NEC). Consult a qualified electrician if you are unfamiliar with proper electrical wiring connections.
• Ensure the supply voltage is correct by comparing it with the luminaire label information.
• Do not install in areas where the operating temperature exceeds the fixture's rated temperature.
• Do not modify the fixture in any way. Any modifications may void the warranty and create safety hazards.
• This product must be installed by a person familiar with the construction and operation of the product and the hazards involved.

3. Package Contents

Verify that all components are present before beginning installation:

• Instruction Manual
• Light fixture (Aether 2in Round Light Engine Trim & LED)
• Mounting Hardware

Image 3.1: WAC Lighting Aether 2in Round Light Engine Trim & LED. This image shows the complete recessed lighting trim with its black and white finish, ready for installation.

4. Setup and Installation

Before You Begin:

• Turn off power at the circuit breaker or fuse box.
• Ensure you have the necessary tools: screwdriver, wire strippers, electrical tape, and safety glasses.
• Confirm that the compatible new construction housing (HR-2LED-H13A or HR-2LED-H13AC) is already installed.

Step-by-Step Installation:

1. Prepare the Housing: Ensure the power to the recessed housing is off. Remove any existing trim or components from the housing.
2. Connect Wiring: Locate the wiring connector from the LED light engine. Connect it to the corresponding connector inside the recessed housing. Ensure a secure connection.
3. Insert Trim: Carefully push the Aether 2in Round Light Engine Trim into the recessed housing. The spring clips on the trim will engage with the housing to hold it securely in place. Apply gentle, even pressure until the trim is flush with the ceiling surface.
4. Secure Trim: For some installations, additional mounting hardware may be used to further secure the trim. Refer to the specific instructions provided with your housing for details.
5. Restore Power: Once the trim is securely installed, restore power at the circuit breaker.
6. Test Functionality: Turn on the light switch to verify proper operation and dimming capabilities.

Image 4.1: Dimensional drawing of the WAC Lighting Aether 2in Round Light Engine Trim. This diagram illustrates the physical measurements of the trim, including its 4 1/8 inch overall diameter and 2 5/8 inch aperture, crucial for proper installation planning.

5. Operating Instructions

Standard Operation:

Once installed and power is restored, the Aether LED trim operates like any standard light fixture. Use your wall switch to turn the light on or off.

Dimming Functionality:

This fixture is designed for smooth and continuous dimming down to 1% when used with compatible Electronic Low Voltage (ELV) or 0-10V dimmers. Ensure your dimmer switch is compatible with LED lighting and specifically with ELV or 0-10V systems for optimal performance. Refer to your dimmer's instruction manual for specific operating procedures.

6. Maintenance

The WAC Lighting Aether LED trim requires minimal maintenance.

• Cleaning: To clean the fixture, ensure power is off. Use a soft, dry, or slightly damp cloth. Do not use abrasive cleaners or solvents, as these may damage the finish or electrical components.
• LED Light Engine: The LED light engine is replaceable. If replacement is necessary, ensure power is off and follow the reverse of the installation steps to remove the old engine and install a new, compatible WAC Lighting LED light engine.
• Inspection: Periodically inspect the fixture for any signs of damage or loose connections. If any issues are found, disconnect power and consult a qualified electrician or WAC Lighting customer support.

7. Troubleshooting

If you experience issues with your Aether LED trim, refer to the following common problems and solutions:

8. Technical Specifications

9. Warranty Information

This WAC Lighting product is covered by a 1477-year limited manufacturer's warranty. This warranty covers defects in materials and workmanship under normal use and service. For specific terms, conditions, and claim procedures, please refer to the official WAC Lighting warranty documentation or contact customer support.

10. Customer Support

For further assistance, technical support, or warranty inquiries, please visit the official WAC Lighting store or contact their customer service department.

WAC Lighting Store: Visit WAC Lighting on Amazon