DEWENWILS HRS101F2

Download PDFFree PDF. The Save button below keeps a bookmark and private notes in your account.

DEWENWILS Outdoor Wireless Remote Control Outlet

Model: HRS101F2

User Instruction Manual

1. Introduction

Thank you for choosing the DEWENWILS Outdoor Wireless Remote Control Outlet. This device provides a convenient solution for remotely controlling your outdoor and indoor electrical appliances. Designed for durability and ease of use, it features a weatherproof construction and a long-range remote control. Please read this manual thoroughly before use to ensure proper operation and safety.

DEWENWILS Outdoor Wireless Remote Control Outlet and Remote

Image 1: DEWENWILS Outdoor Wireless Remote Control Outlet and Remote

2. Safety Information

  • Ensure the total current of connected appliances does not exceed 15A.
  • Do not immerse the outlet in water or expose it to direct water streams.
  • For outdoor use, install the outlet vertically with the receptacles facing downwards, at least 2 feet above the ground, to prevent water ingress.
  • Always ensure the plug is fully inserted into the wall outlet.
  • Do not disassemble or modify the device. Refer all servicing to qualified personnel.
  • Keep out of reach of children.
Weather-resistant outlet installed vertically, with warnings against immersion and direct water streams.

Image 2: Proper installation for weather resistance, avoiding immersion and direct water exposure.

3. Package Contents

  • 1 x DEWENWILS Outdoor Wireless Remote Control Outlet (HRS101F2)
  • 1 x Remote Control (with CR2032 3V battery included)
  • 1 x User Manual

4. Setup

The DEWENWILS Outdoor Wireless Remote Control Outlet is pre-programmed for immediate use. No complex setup is required for basic operation.

Initial Setup:

  1. Plug the outdoor remote control outlet into a grounded 125V AC electrical receptacle.
  2. Connect your appliance(s) to the two grounded AC outlets on the remote control unit.
  3. The remote control is pre-paired. Press the 'ON' or 'OFF' button on the remote to control the connected appliances.
Hand holding remote, controlling an outdoor outlet plugged into a wall, with a green indicator light.

Image 3: Easy plug-and-play setup with the remote control.

Re-Programming / Pairing the Remote:

If the remote control loses its pairing or you wish to pair a new remote, follow these steps:

  1. Press the programming button on the receiver (the outlet unit) until the indicator light begins to flash slowly.
  2. Release the button. Then, press the 'ON' button on your remote control.
  3. The indicator light will stop flashing and remain on, indicating successful programming.

Video 1: Demonstrates the re-programming process for the remote control outlet.

5. Operating Instructions

Using the Remote Control:

  • Press the 'ON' button on the remote control to turn on the connected appliances.
  • Press the 'OFF' button on the remote control to turn off the connected appliances.
  • The remote operates with a range of up to 100 feet in open areas and can transmit through walls and doors.
Person inside a house using the remote control to turn on outdoor lights, demonstrating the signal's ability to pass through walls.

Image 4: Remote control functionality from indoors for outdoor lighting.

Using the Manual Button:

The outlet unit also features a manual button for direct control:

  • Press the button on the top of the outlet unit to manually toggle the power ON or OFF.
  • The indicator light on the unit will illuminate when power is ON.

6. Maintenance

  • Regularly inspect the unit and connected cords for any signs of damage or wear.
  • Clean the unit with a soft, dry cloth. Do not use abrasive cleaners or solvents.
  • Ensure the battery in the remote control is replaced when its range or responsiveness decreases. The remote uses a CR2032 3V battery.

7. Troubleshooting

  • Appliance not turning ON/OFF: Check if the outlet unit is properly plugged into the wall. Ensure the appliance is correctly plugged into the outlet unit. Verify the remote control battery is functional. Try re-pairing the remote control as described in Section 4.
  • Reduced Remote Range: Replace the remote control battery. Ensure there are no major obstructions (e.g., thick concrete walls, large metal objects) between the remote and the receiver.
  • Indicator Light not illuminating: Check the power supply to the wall outlet. If the unit is connected to a GFCI outlet, ensure it has not tripped.
  • Interference with other devices: The unit is designed for non-interference. If interference occurs, try re-pairing the remote control.

8. Specifications

SpecificationDetail
Model NumberHRS101F2
Voltage125 Volts
Max Current15A
Max Power (Resistive)1875W
Max Power (Tungsten)1000W
Horsepower1/2HP
Control RangeUp to 100 feet (open area)
Outlets2 Grounded AC Outlets
Cord Length7-inch SJTW 14/3C
MaterialPolycarbonate (PC)
Remote BatteryCR2032 3V (included)
CertificationsETL, FCC
Product Dimensions5.75 x 1.57 x 4.02 inches
Weight8.01 ounces
Diagram showing the dimensions of the DEWENWILS outdoor remote control outlet and its remote.

Image 5: Dimensions of the outlet and remote control.

9. Warranty and Support

DEWENWILS products are designed for reliability and performance. For warranty information or technical support, please refer to the contact details provided on the product packaging or visit the official DEWENWILS website. Keep your purchase receipt for warranty claims.

© 2025 DEWENWILS. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.