1. Product Overview
The Garage-Pro Front Bumper Bracket is a replacement component designed to securely hold the front bumper of your Ford Fiesta in its correct position. This specific bracket is for the Right Hand (passenger) side of the vehicle and is constructed from durable plastic, ensuring a direct fit and reliable performance.
This image shows the Garage-Pro Front Bumper Bracket, a black plastic component designed to securely hold the front bumper in place.
2. Vehicle Compatibility
This bumper bracket is compatible with the following vehicle models:
- Ford Fiesta (Sedan models only): 2011, 2012, 2013, 2014, 2015, 2016, 2017
This part is specifically designed for the Front, Passenger (Right Hand - RH) Side of the vehicle.
An overhead diagram of a car's front, clearly marking the Right Hand (RH) and Left Hand (LH) sides to assist in correct part placement.
3. Package Contents
Upon opening the package, you should find the following item:
- 1 x Garage-Pro Front Bumper Bracket (Right Hand / Passenger Side)
4. Safety Information
Always prioritize safety when working on your vehicle. Please observe the following precautions:
- Wear appropriate personal protective equipment, including safety glasses and gloves.
- Ensure the vehicle is parked on a level surface with the parking brake engaged.
- If lifting the vehicle, use appropriate jack stands to secure it.
- If you are unsure about any step, consult a qualified automotive professional.
5. Tools Required
The following tools are typically required for bumper bracket replacement:
- Ratchet and Socket Kit
- Screwdriver Set (Phillips and Flathead)
- Trim and Molding Removal Tools (plastic pry tools)
- Replacement Clips (if existing ones are damaged during removal)
- Screws (if existing ones are damaged or missing)
This image illustrates common tools needed for automotive work, including a ratchet, socket set, screwdriver, and trim removal tools.
6. Installation Instructions
The following steps outline the general procedure for replacing a front bumper bracket. Specific vehicle disassembly may vary. Professional installation is recommended.
- Prepare the Vehicle: Park the vehicle on a flat, stable surface. Engage the parking brake.
- Access the Bumper Area: Carefully remove any fasteners, clips, or screws that secure the front bumper cover to the vehicle body, wheel wells, and grille area. Use trim removal tools to avoid damaging paint or plastic components.
- Partially Remove Bumper Cover: Gently pull the bumper cover away from the vehicle to gain access to the bumper bracket. You may not need to fully remove the bumper cover, but ensure enough access to the bracket.
- Locate and Remove Old Bracket: Identify the damaged or old bumper bracket on the passenger side. Remove any bolts or fasteners holding it in place.
- Position New Bracket: Align the new Garage-Pro Front Bumper Bracket (AE8Z17E856A) with the mounting points on the vehicle frame and the bumper cover. Ensure it is oriented correctly for the passenger side.
- Secure New Bracket: Install the bolts or fasteners to secure the new bracket firmly in place. Do not overtighten.
- Reassemble Bumper and Trim: Carefully re-position the bumper cover and secure all previously removed fasteners, clips, and screws. Ensure all gaps are even and the bumper is flush with the vehicle body.
- Verify Fitment: Double-check that the bumper is securely attached and that the new bracket holds it firmly.
A side view of the black plastic bumper bracket, highlighting its contours and mounting points.
7. Maintenance
This bumper bracket is designed for long-lasting performance with minimal maintenance. Periodically inspect the bracket and surrounding bumper area for any signs of damage, cracks, or loose fasteners, especially after any minor impacts or off-road driving. Clean as needed with mild soap and water.
8. Troubleshooting
If the bumper does not fit correctly or appears misaligned after installation, consider the following:
- Re-check Mounting Points: Ensure all fasteners are tightened and the bracket is properly seated in its designated location.
- Verify Part Correctness: Confirm that the correct bracket for the specific side (passenger/driver) and vehicle model year is used.
- Inspect for Obstructions: Check for any debris or other components preventing the bumper from seating flush.
9. Product Specifications
| Feature | Detail |
|---|---|
| Brand | Garage-Pro |
| Model Number | AE8Z17E856A |
| OEM Part Number | AE8Z17E856A |
| Partslink Number | FO1043128 |
| Material | Plastic |
| Position | Front, Passenger Right Side |
| Item Dimensions (L x W x H) | 9 x 6 x 3 inches |
| Item Weight | 1 pound |
| UPC | 195975453378 |
An angled view of the black plastic bumper bracket, showing its structural design and attachment points.
10. Warranty and Support
This Garage-Pro item comes with a 1-year UNLIMITED mileage warranty coverage. For any questions, technical assistance, or to initiate a warranty claim, please contact Garage-Pro customer support through the retailer where the product was purchased or visit the official Garage-Pro website for contact information.
