Energizer CR1632

Energizer CR1632 Lithium Battery 3V User Manual

Model: CR1632

1. Introduction

This manual provides essential information for the safe and effective use of the Energizer CR1632 3V Lithium Coin Cell Battery. Please read these instructions carefully before use and retain them for future reference. This battery is designed for use in various small electronic devices requiring a CR1632 cell, such as car key fobs, watches, calculators, and medical devices.

Energizer CR1632 Lithium Battery 3V in blister packaging

Image: Two Energizer CR1632 3V Lithium Coin Cell Batteries in their original blister packaging, showing the battery specifications and brand logo.

2. Safety Information

WARNING: Keep batteries out of reach of children. Swallowing can lead to serious injury or death in as little as 2 hours due to chemical burns and potential perforation of the esophagus. If swallowed, immediately seek medical attention.

  • Do not recharge, disassemble, heat, or dispose of in fire. This may cause explosion, leakage, or fire.
  • Do not mix new and used batteries, or different types of batteries.
  • Ensure correct polarity (+ and -) when installing.
  • Store batteries in their original packaging until ready for use.
  • Avoid short-circuiting the battery terminals.

3. Setup and Installation

The installation process for CR1632 batteries typically involves opening the device's battery compartment, removing the old battery, and inserting the new one with correct polarity. Specific steps may vary depending on the device.

  1. Identify Battery Compartment: Locate the battery compartment on your electronic device. This is often secured with a small screw or a latch.
  2. Open Compartment: Use an appropriate tool (e.g., a small screwdriver, a coin, or the device's emergency key) to open the battery compartment. Refer to your device's manual for precise instructions.
  3. Remove Old Battery: Carefully remove the depleted CR1632 battery. Note its orientation (positive (+) side up or down).
  4. Insert New Battery: Place the new Energizer CR1632 battery into the compartment, ensuring the positive (+) and negative (-) terminals align correctly with the device's markings.
  5. Close Compartment: Securely close the battery compartment. Test the device to ensure proper function.

4. Operating Instructions

The Energizer CR1632 battery provides a stable 3-volt power supply for compatible devices. Once installed correctly, the device should operate as intended. No specific operating procedures are required for the battery itself beyond proper installation.

5. Maintenance and Storage

  • Storage: Store unused batteries in a cool, dry place at room temperature, away from direct sunlight and extreme temperatures. Keep them in their original packaging to prevent short-circuiting.
  • Handling: Avoid touching the battery terminals with bare hands, as oils and dirt can affect conductivity.
  • Cleaning: If battery contacts in a device appear dirty, clean them with a cotton swab lightly moistened with rubbing alcohol before inserting a new battery.

6. Troubleshooting

If your device does not function after replacing the battery:

  • Check Polarity: Ensure the battery is inserted with the correct positive (+) and negative (-) orientation.
  • Verify Battery Type: Confirm that CR1632 is the correct battery type specified for your device.
  • Inspect Contacts: Check for any corrosion or debris on the device's battery contacts and clean if necessary.
  • Test Battery: If possible, test the new battery with a battery tester to ensure it is charged.
  • Consult Device Manual: Refer to your device's instruction manual for specific troubleshooting steps.

7. Specifications

FeatureSpecification
Model NumberCR1632
Voltage3V
Battery Cell CompositionLithium
Item Weight0.01 ounces
Package Dimensions5.67 x 4.96 x 0.31 inches
Number of Batteries (in this pack)2
Recommended UsesWatches, Key Fobs, Calculators, Small Electronics

8. Disposal

Do not dispose of batteries in household waste. Lithium batteries should be recycled or disposed of according to local regulations. Many retailers and community centers offer battery recycling programs. Contact your local waste management authority for information on proper disposal in your area.

9. Warranty and Support

Energizer batteries are manufactured to high-quality standards. For information regarding product warranty or customer support, please refer to the official Energizer website or contact their customer service directly. Keep your purchase receipt as proof of purchase.

Related Documents - CR1632

Preview Energizer UE30035C 30000mAh Portable Power Bank User Manual and Specifications
Comprehensive guide for the Energizer UE30035C 30000mAh portable power bank, covering specifications, safety instructions, usage, charging, warranty, and customer support.
Preview Energizer Smart WiFi Indoor Camera EIP1-1003 Quick Start Guide
Get started quickly with the Energizer Smart WiFi Indoor Camera (EIP1-1003). This guide provides essential setup, installation, and operational information for your home security needs.
Preview Energizer Smart WiFi Video Doorbell Quick Start Guide | EOD1-1002-2002
Quick start guide for the Energizer Smart WiFi Video Doorbell (Model EOD1-1002-2002). Learn how to set up, connect, and use your video doorbell with step-by-step instructions and troubleshooting tips.
Preview Energizer UE10050CC 10000mAh Power Bank - User Manual & Specifications
Get detailed specifications, usage instructions, and charging guidance for the Energizer UE10050CC 10000mAh portable power bank. Learn about PowerSafe management and warranty information.
Preview Energizer Smart WiFi Video Doorbell Quick Start Guide | EOD1-1002-2002
Get started with your Energizer Smart WiFi Video Doorbell (EOD1-1002-2002). This quick start guide covers setup, app connection, live view, recording, and troubleshooting for seamless home security.
Preview Energizer Smart Video Doorbell EOD1-1001-SIL Quick Start Guide
A quick start guide for the Energizer Smart Video Doorbell (Model EOD1-1001-SIL), covering package contents, app pairing, setup, voice activation with Alexa and Google Assistant, and troubleshooting.